文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > IT/计算机 > 互联网 > 高速接口设计
侵权投诉

高速接口设计

高速I/O接口设计

■As rx_ctrldetect and rx_patterndetect are not asserted, no control

characters or word alignment patterns are detected.

The rx_dataout signal is stuck at 0x00. All of this information indicates that

something is wrong with the data that should be present on rx_datain.■

Inspection of the loopback cables showed that the SMA connector was not connected

on the n half of the differential pair. Correct connection provided the receiver with the

signal it requires for correct operation.

No Synchronization—No tx_ctrlenable

Figure12 shows a screenshot of a SignalTap II plot taken from the example design

with a deliberate fault to cause a failure.

In this scenario, both the transmitter and receiver PLLs are operating correctly and the

CDR is in the LTD mode, which indicates that data is received. The data transmitted is

a simple hexadecimal count, but in this scenario the data received appears corrupt

and errors are detected.

Figure12.

高速接口设计

No Synchronization—Case 1

In this scenario, you may be tempted to focus on the signals that are toggling—

rx_errdetect and rx_disperr—which indicate 8B10B and or disparity errors. Do

not overlook signals that are not toggling—tx_ctrlenable, rx_ctrldetect,

rx_patterndetect, and rx_syncstatus. You should observe that the

rx_syncstatus is not toggling and is deasserted, which indicates that the receiver

has not synchronized to the incoming data.

In basic mode, for the receiver to correctly synchronize it must detect a valid control

character (0xBC in this case) in the received datastream. Figure12 shows that no

control characters or word alignment patterns are detected by the receiver, despite the

transmitter interrupting the count data with a 0xBC character.

In this case, the receiver cannot detect the transmitted 0xBC character, because the

data generator logic is not instructing the transmitter to encode the 0xBC character as

a control code by asserting the tx_ctrlenable signal and so is transmitted as a data

character.

The example design that demonstrates this scenario has a feature to switch off the

necessary tx_ctrlenable assertions. Re-enabling the correct encoding of the 0xBC

character as a control character allows the receiver to correctly detect the control code,

word align, and synchronize correctly.

上一页第15页

你可能喜欢

  • 软件接口设计
  • 接口设计说明
  • 接口设计文档
  • 接口设计方案
  • 接口设计规范
  • 接口技术课程设计

热门文档

相关文档

  • 高速USB接口设计

    第17卷V01.17 第3期No.3 电子设计工程ElectronicDesignEngineering 2009年3月Mat.2009 高速USB接口设计甄国涌.张森峰(中北大学电子潮试技术国家重点实验室,山西...

  • 高速USB接口设计

    第17 卷 第3期 Vol.17 No.3 电子设计工程 Electronic Design Engineering 2009 年 3 月 Mar.2009 高速 USB 接口设计甄国涌 , 张森峰(中北大学 电子测试技术...

  • DDR+SDRAM与FPGA的高速接口设计

    DDR+SDRAM与FPGA的高速接口设计_信息与通信_工程科技_专业资料。介绍关于FPGA DDR 控制器的专业文档可轴糕器件盛.属 DDR 电子测豢技术 ELECTR()NIC 第3l卷第n...

  • 基于Xilinx Spartan6的高速接口设计

    基于Xilinx Spartan6的高速接口设计_电子/电路_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 基于Xilinx Spartan6的高速接口设计_电子/电路_工程科技_专业...

  • TS201高速通信接口设计及实现

    ADI公司TigerSHARC系列DSP芯片TS201性能优越,在高速实时信号处理中得到广泛应用,而其中对TS201的通信接口设计成为保证其高速实时性能的关键。对TS201与FPGA之间两种主要...

  • STM32F103的高速以太网接口设计

    STM32F103的高速以太网接口设计_计算机硬件及网络_IT/计算机_专业资料 暂无评价0人阅读0次下载举报文档 STM32F103的高速以太网接口设计_计算机硬件及网络_IT/...

  • 基于STM32F107的高速以太网接口设计与应用

    基于STM32F107的高速以太网接口设计与应用_工学_高等教育_教育专区。基于STM32F107的高速以太网接口设计与应用Network and Multimedi 文章编号: 1002-8684 (2011) 09...

  • 【论文】Gbps试验系统中高速串行接口的设计与实现

    Gbps试验系统中高速串行接口的设计与实现_专业资料。介绍Gbps无线通信试验系统中高速串行数据接口的设计与实现。按照Gbps无线通信试验系统对高速串行数据的传输要求,数据...

  • 基于FPGA的高速通信接口设计

    基于FPGA的高速通信接口设计_信息与通信_工程科技_专业资料。基于FPGA的高速通信接口设计2005年9月 第3期 实验科学与技术 基于FPGA的高速通信接口设计。 A砸ghSpeed...

  • 基于TMS320C6455的高速SRIO接口设计

    基于TMS320C6455的高速SRIO接口设计_信息与通信_工程科技_专业资料。RapidIO互连架构是一个开放的标准,满足了嵌入式基础设施在应用方面的广泛需要。它将是未来十几年嵌...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email