高速I/O接口设计
The design should implement a valid reset sequence and also supply the ALT2GXB
instance with meaningful data that allows simple debugging. A count allows manual
verification but a more realistic test is a pseudo random binary sequence (PRBS) code,
which requires a data checking component to ease verification of pseudo random
data.
The design should also correctly send synchronization control characters to allow the
receiver state machine to synchronize.
The design may either be implemented using the ALT2GXB loopback feature, or an
external loopback may be implemented on board for a more comprehensive test that
includes PCB traces and connectors.
Example Design
The example design included with this application note targets the Stratix II GX signal
integrity board and implements a single transceiver pair that relies on an external
loopback connection.
The project contains a simple reset state machine, which monitors and waits for the
assertion of the respective pll_locked, rx_pll_locked, and rx_freqlocked
signals before transmitting and receiving data.
The project contains a simple data generator that can present either an 8-bit count
value or a PRBS onto the tx_datain port of the transmitter, but also inserts a
synchronization word (0xBC) every 256 words, which allows the receiver to
synchronize.
The project also contains a SignalTap II file that allows the internal transceiver status
signals in the design to be monitored when it is running on the device.
After successful reset initialization, pll_locked and rx_freqlocked are high.
rx_pll_locked may toggle, which is OK as the receiver is in lock-to-data mode if
rx_freqlocked is high. The rx_syncstatus signal is asserted and periodic
rx_patterndetect and rx_ctrldetect assertions on receiving a control
character (0xBC) every 256 words may be observed.
Observing the 8 bit tx_datain and rx_dataout busses allows you to confirm that
data is correct. With SignalTap II verification, the sample clock in the example design
is rx_clkout, which is asynchronous to tx_clkout that presents data to the
tx_datain port. You may see occasional discrepancies between tx_datain and
rx_dataout in the SignalTap II analyzer because of this asynchronicity.
If no errors are detected, rx_disperr and rx_errdetect remain de-asserted.
The project also contains a testbench, which you may use with the ModelSim-Altera
simulator to verify this design. Compile and run the simulation for approximately
10μs to see correct data and synchronization.
This design can provide verification on hardware that the power supplies, clocks, and
resets are sufficiently stable for a basic single-channel transceiver design. This design
only targets a single channel and does not reflect a full design, but you can scale up
this design.
1The design is for use on the Stratix II GX signal integrity board, but you may modify it
for use on other suitable boards.
第17卷V01.17 第3期No.3 电子设计工程ElectronicDesignEngineering 2009年3月Mat.2009 高速USB接口设计甄国涌.张森峰(中北大学电子潮试技术国家重点实验室,山西...
第17 卷 第3期 Vol.17 No.3 电子设计工程 Electronic Design Engineering 2009 年 3 月 Mar.2009 高速 USB 接口设计甄国涌 , 张森峰(中北大学 电子测试技术...
DDR+SDRAM与FPGA的高速接口设计_信息与通信_工程科技_专业资料。介绍关于FPGA DDR 控制器的专业文档可轴糕器件盛.属 DDR 电子测豢技术 ELECTR()NIC 第3l卷第n...
基于Xilinx Spartan6的高速接口设计_电子/电路_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 基于Xilinx Spartan6的高速接口设计_电子/电路_工程科技_专业...
ADI公司TigerSHARC系列DSP芯片TS201性能优越,在高速实时信号处理中得到广泛应用,而其中对TS201的通信接口设计成为保证其高速实时性能的关键。对TS201与FPGA之间两种主要...
STM32F103的高速以太网接口设计_计算机硬件及网络_IT/计算机_专业资料 暂无评价0人阅读0次下载举报文档 STM32F103的高速以太网接口设计_计算机硬件及网络_IT/...
基于STM32F107的高速以太网接口设计与应用_工学_高等教育_教育专区。基于STM32F107的高速以太网接口设计与应用Network and Multimedi 文章编号: 1002-8684 (2011) 09...
Gbps试验系统中高速串行接口的设计与实现_专业资料。介绍Gbps无线通信试验系统中高速串行数据接口的设计与实现。按照Gbps无线通信试验系统对高速串行数据的传输要求,数据...
基于FPGA的高速通信接口设计_信息与通信_工程科技_专业资料。基于FPGA的高速通信接口设计2005年9月 第3期 实验科学与技术 基于FPGA的高速通信接口设计。 A砸ghSpeed...
基于TMS320C6455的高速SRIO接口设计_信息与通信_工程科技_专业资料。RapidIO互连架构是一个开放的标准,满足了嵌入式基础设施在应用方面的广泛需要。它将是未来十几年嵌...
热门文档