International Journal of Minerals, Metallurgy and Materials Volume 17, Number 6, December 2010, Page 715 DOI: 10.1007/s12613-010-0379-4
A process model for BOF process based on bath mixing degree
Guang-hui Li1), Bao Wang1), Qing Liu1), Xin-zhong Tian1,2), Rong Zhu1), Li-ning Hu2), and Guo-guang Cheng1)
1) School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China 2) Research and Development Center, Xingtai Steel Co. Ltd., Xingtai 054027, China (Received: 11 January 2010; revised: 9 February 2010; accepted: 21 February 2010)
Abstract: The process model for BOF process can be applied to predict the liquid steel composition and bath temperature during the whole steelmaking process. On the basis of the traditional three-stage decarburization theory, the concept of mixing degree was put forward, which was used to indicate the effect of oxygen jet on decarburization. Furthermore, a more practical process model for BOF steelmaking was de-veloped by analyzing the effect of silicon, manganese, oxygen injection rate, oxygen lance height, and bath temperature on decarburization. Process verification and end-point verification for the process model have been carried out, and the verification results show that the predic-tion accuracy of carbon content reaches 82.6% (the range of carbon content at the end-point is less than 0.1wt%) and 85.7% (the range of carbon content at end-point is 0.1wt%-0.7wt%) when the absolute error is less than 0.02wt% and 0.05wt%, respectively. Keywords: steelmaking; basic oxygen furnace (BOF); decarburization; modelling; prediction
[This work was financially supported by the New Century Excellent Talents Program of the Ministry of Education of China (No.NCET 07-0067) and the National Natural Science Foundation of China (No.50874014).]
operation, and the hit rate is lower at the steelmaking end-point. In the paper, a process model for these kinds of BOF was developed to improve the control accuracy at the steelmaking end-point.
The traditional three-stage decarburization theory for BOF is shown schematically in Fig. 1 [2], and this theory is widely accepted by metallurgical researchers and engineers. However, its practicability is limited because it does not re- flect the specific effects of main factors on decarburization. In the steelmaking process, silicon content, manganese con- tent, oxygen injection rate, bath temperature, and oxygen lance height are main factors that can influence decarburiza- tion [3-6], and this paper focused on the research on the ef- fects of these factors on decarburization.
The three-stage decarburization theory can be expressed as follows.
The decarburization rate formula in the first stage:
1. Introduction
Developed by researchers, most models for BOF control are the end-point control model, whose targets are the con- trol of bath composition and temperature at the end-point [1]. With the development of metallurgical processes, process control for BOF has been receiving more and more attention. Carbon content and bath temperature control at the steel- making end-point, raw materials consumption, splash, slag getting dry, and some other process problems are all influ- enced by process control. On the progress of detection tech- niques in steelmaking processes, the capability of acquiring process information is becoming stronger than before, which makes process control possible. In addition, a process model has become one of development trends in the field of math- ematic models for BOF control. In China, most middle and small-sized converters have not installed dynamic detection equipment, and they mainly rely on the experience gained in
Corresponding author: Qing Liu E-mail: qliu@ustb.edu.cn
© University of Science and Technology Beijing and Springer-Verlag Berlin Heidelberg 2010

万方数据
A process model for BOF process based on bath mixing degree_专业资料。IentoaJunlMirl,ntrainlora ofneasMetlralgya trl undMaeisaIentoaJunlMirl...
Process Capability Analysis for Warping Calculations Based on Weibull Distribution Model USL [结果分析] 能力条形图没有显示在假想的模型和数据之间存在严重的差异...
Each wafer allows for a maximum efficiency – 20...process if top/bottom (impurity gettering) for ...on WFCD ISRA GP – Wafer Quality Sorting with ...
6页 1下载券 A Process Model for Be... 暂无评价 15页 免费Lin...We work based on client’s needs, recruiting top practitioners in specific ...
and FE model of wing structure are achieved based on CAD parametric technology...1204 In the process of FE modeling, a variety of templates in design ar...
ON CONTIKI/COOJA PLATFORM A Master Thesis ...process model, event scheduling mechanism and system...
productiontheprocessafter Recently,moreandmorescholarsdoresearch on the Quailtycost process(A3)Thefeeon quailtycost,andputforwardthequailtycostmodel〔i】.Plunkett...
Good avalanche safety is a continuous process, ...Alarms based on he same concept have already ...The new model could help inform energy-related ...
Based on the empirical survey on the diffusion channels for technological ...The current studies focus mostly on diffusion model, motivation, process, ...
Research of Interactive Measurement Based on 3D ...The algorithm can accelerate the process of ...itself is a three-dimensional object in model ...
热门文档