802.11跨层优化

(i.e. it still has packets to send). If the packet transmission is successful or the packet has exceeded its retransmission limit, the MAC goes back to the (0,0) state. In the retransmission limit is exceeded, the MAC packet is dropped, while if the packet is successful, the MAC dequeues the packet from its queue following the post backoff process. This is represented by Equation (6). Finally, when the MAC has transmitted all the packets in the queue and has done the post backoff procedure, it will go back to idle state. The idle state is exited whenever packets from the application layer are arriving to the MAC queue.
Based on the analysis, we can compute the probability of being in the state (0,0), denoted as b0,0, as:
Here E[Nc] is the number of collisions before a frame is transmitted successfully and E[BD] is the expected backoff delay for transmitting a frame that includes frozen periods of the backoff counter and non frozen periods of the backoff counter. Let Ts and Tc represent the duration of a successful transmission and collision. They are represented as follows.
Ts=Header+E[P]+SIFS+δ+ACK+DIFS+δ Tc=Header+E[P*]+DIFS+δ
(12)
Here E[P*] is the average length of the packet payload involved
in a collision, δis the duration of an empty slot. Then, the packet loss introduced by a frame delay can be calculated as:
Dend_to_end
where, A0,0by:
Pframe_delay_loss=(1 τ)E[D] (13)
(8) A0,0
The optimal retransmission limit for a frame bounded by the delay constraint is given by:
=2(1 2qc)(1 qc)(1 π0) and B0,0 is given
B0,0
B0,0=2(1 2qc)(1 qc)(1 π0)(W0+1+qcπ1(2W0+1))+4W0qc2(1 (2qc)m 1)(1 qc)(1 π0)
+qc2(1 qcm 1)(1 2qc)(1 π0)+(1 π1)(1 2qc)(1 qc)
Having calculated b0,0, we can express the probability τ that a WSTA transmits in a randomly chosen slot time.
mmax=
Dend_to_end
E[D]
(14)
Here Dend_to_end is the maximum delay tolerated for a frame at the MAC layer. Note that depending on the compression strategy deployed at the application layer, Dend_to_end will vary per frame. For instance, in an MPEG-4 coded bitstream, I, P and B-frames packets will have different Dend_to_end values. In the worse case, the WSTA has to transmit a packet mmax times before it can be successfully delivered at the receiver. Hence,
mmax
τ=∑bi,0 b0,0 (1 π1).
i=0
m
Simplifying the above equation yields:
(1 qc)π1+(1 qc)qcπ1+qc2(1 qcm 1)
τ=b0,0 (9)
1-qc
∑τ(1 τ)
k=1
k 1
≥1 Pframe_delay_loss (15)
1
which leads to:
B. Determination of the optimal backoff stage mopt
P≤(1 τ) (16) frame_delay_lossIn this section, we determine the optimal backoff stage, mopt,
based on our new application-aware MAC model. At the 2) Packet loss introduced by buffer overflow
application layer, packet losses occur due to two reasons: The above model does not consider the finite buffer at the packets being lost due to link erasures or arriving at the MAC. Whenever the application layer sends its packet to MAC application layer after their decoding time and packets lost due layer without considering the state of the wireless channel, to MAC buffer overflows: MAC buffer overflow can occur (see [5] for more details). To Ploss=Pframe_delay_loss+Poverflow_loss (10) capture the effects of this buffer overflow, we use M/M/1/K
queuing model as an approximation to study its effect. The
While the loss due to link erasures decreases with increasing blocking probability for a M/M/1/K model whose buffer size is retransmission limit, the loss due to buffer overflow increases K is given by: with increasing retransmission limits. In [5], we presented a Kstrategy to optimally select the retransmission limit that λ λ minimizes the overall MAC packet loss due to buffer overflow 1
(17) and link errors. However, in our previous work, our analysis PK= K1
was based on a simplified MAC model, which consisted of a λ
1 two state Markov model. In this paper, we compute the optimal
retransmission limit based on the realistic MAC DCF model
presented in the previous section. where λ and µ represent the arrival and departure rate into 1) Packet loss introduced by frame delay
the queue respectively. Modeling our system as a M/M/1/K
From [3], the expected frame delay can be expressed by
E[D]=E[Nc](E[BD]+Tc)+(E[BD]+Ts) (11)
application layer to achieve the best video ...Zhang, “An integrated scheme for automatic video...Cross-layer Optimized Wireless Multimedia ...
cross-layer design are demonstrated for video ... or the application layer can adapt its ...to reach optimized usage of the wireless channel....
Integrated MAC and Routing Protocol for Wireless ...solutions optimized for specic application classes. ... cross-layer integration, MAC, power-saving mode...
Proxy-driven ratedistortion optimized video ... MAC layer FEC/ARQ, application layer FEC and ...Following the discussion of channel modeling in ...
Cross-layer optimization for OFDM wireless ...provisioning when application performance is the key...when they are optimized for the sum of ...
cross-layer optimized system to maximize the ...layer are integrated for wireless ad hoc networks... video encoder resides in the application layer. ...
A cross-layer framework for wireless LAN QoS ...They can be assigned directly by the application ...from the performance modeling to a compact policy...
wireless home networks as an application example. ... utilizing the rate-distortion optimized framework ...The bene?t of cross-layer video rate adaptation...
Video Transmission over Wireless LANs Pierre Ferr?...and can also be integrated onto handheld devices....Layer Application Transport Network Link/MAC Packet...
over Wireless Networks with Heterogeneous L_专业...optimized rate allocation among multiple video ...MAC layer and the applicationlayer video rate ...
热门文档