Application of the FactSage to Predict the Ash Melting Behavior in Reducing Conditions
787
fol
lowing the coalification process are typically found in veins. Calcium, from calcite, may interact with transforming clay minerals to produce calcium-rich aluminosilicate ash particles and lower the AFT. The variation of pyrite content in Huainan coals indicates the different geological conditions during the coalification process. Pyrite in coals can have a significant influence on ash fusion process. It decomposes and fuses at a relatively low temperature.
4.2 FactSage calculation and analysis The FactSage calculations were performed from 800°C to 1600°C. Fig.1 shows clearly the mass percent of liquid phase as the function of temperature for six typical Huainan coal ash samples. Although the amount of liquid phase is fairly low at 1000°C,a percentage of which is definitely present, this temperature is not reflected by AFT analysis. The mass percentage of liquid phase formed during the heating process varied with coal ash samples over the temperature ranges. For HN115 and HN119, the initial liquid formation temperature is at about 1000°C. With an increase in temperature, the mass percentage of liquid phase increases quickly by 75% of the overall material for HN115 at 1400°C and HN119 at 1450°C respectively, which is quite fit for the tested AFT. For HN106, the initial liquid formation temperature is higher than that of HN115 and HN119 at about 1070"C. From 1070°C to 111O"C, the liquid phase increases very sharply from very low percentage to 35%. Over lllO"C, the formed liquid increases smoothly by 63% at 1600"C, which means about 40% solid present in the slag and demonstrates why the HN106 AFT is so high. s 100, I
teristics. From 800°C to lOOO"C, the proportion of feldspar phase increases smoothly. At about 1000°C, the proportion of feldspar phase increases sharply and reaches maximum at temperature 1020°C. At temperature over 1O2OoC,the proportion of feldspar phase and quartz decreases smoothly which results in a rapid increase in the proportion of liquid phase. Quartz disappeared at 1200°C. Feldspar phase disappeared at 1400°C which has excellent agreement with the tested AFT (see Table 1). For temperature increase from over 1400"C to 1600°C the mass percentage of mullite decreases from 23% to 3.4% and leucite begin to decline from 3% to 1.5%.
80 Z
60
8
40
50k/ temperature,"C
Figure 2 The ash transformation of HN115 coal as the function of temperature under reducing condition o melilite; A feldspar; o SiOz quartz; x AI6Si2Ol3 mullite; n KAlSi206leucite;+ TiO, rutile; -(FeO) (TiO,) ilmenite; n Si02tridymite;+slag liquid; 0 mullite
temperature,"C
Figure 1 Mass percentage of liquid phase for representative Huainan coal ash samples HN115; ---- HN119; ---mC13; KLI; ---HNPOl; HN106 ~~
4.3 AFT measurements and the FactSage predictions Two typical Huainan coals, HN115 with FT 1400°C and HN106 with FT higher than 1500"C,were selected for the comparison of tested FT and predicted FT with the addition of CaO flux. An equivale
nt CaO level of 8%, 15%, 20%, 25%, 30%, 35%, 42% of ash mass were selected to estimate the results. The predicted FT was defined as the temperature at which the formed liquid phase reaches 75% of the total material. The comparison results are shown in Table 3. The results show clearly that the measured FT and the predicted FT are quite close with the maximum temperature difference less than 74°C which is within acceptable range. 4.4 The experiments investigation of ash transformation by XRD Figure 3 shows the main mineral components change of HN115 coal ash at different temperature under a simulated gasification environment (6O%CO, 4O%co2). As temperature increases, thermal decomposition, transformation and interaction and phase change occur among the components. Around 1150"C, anorthite (CaAl2Si~O8) becomes stable probably due to partial melting of the phase assemblage. Quartz and anhydrite decrease while mullite increases. From 1150°C to Chinese J. Ch. E. 14(6) 784 (2006)
Figure 2 shows the main calculation results for ash transformation of HN11.5 coal with the temperature increase. The data shows that melilite (Ca,Na)2(A1,Mg,Fe2+)(Si,A1)207, feldspar[XAl(1-2)Si(3.2) 0 8, X in the formula can be sodium, and/or potassium, and/or calcium], quartz (Si02), mullite (A16Si2013), cordierite (Mg2A1&5018), AlP04, leucite (KAlSi206), rutile (Ti02), ilmenite (FeO)(TiOz) was formed at 800°C. As the temperature increases to about 1000°C,liquid starts to form. About all melilite and 50% mullite phase react to form feldspar phase which has significant effect on the ash fusion charac-

Chem. Eng., 14(6) 784—789 (2006) Application of the FactSage to Predict the Ash Melting Behavior in Reducing Conditions* LI Hanxu(李寒旭)a,**, ...
ago.The FactSage package preparedbycriticalevaluationand optimization ofa11 ...Application oftheFactSagetoPredicttheAshMeltingBehaviorinReducingConditionsAsshown...
melting point and viscosity of slag in steelmaking...the distribution behavior of P2O5 between solid solution...(2) The calculated results by FactSage indicat...
The computer software package FactSage was used to...These models predict the AFTs of coal ash ...ers), the content of the strongly reducing gas ...
热门文档