文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > Control of Coating Properties of Abradable Seals by On-Line Process Diagnostics
侵权投诉

Control of Coating Properties of Abradable Seals by On-Line Process Diagnostics

The efficiency of gas turbines is highly dependent upon the clearance between compressor housing and rotating blades. Abradable seal coatings are employed to minimize the clearance and control the over-tip leakage by allowing the blade tips to cut into the

Control of Coating Properties of Abradable Seals by On-Line Process

Diagnostics

E. Lugscheider, J. Zwick

Materials Science Institute, RWTH Aachen University, Germany

M. Hertter

MTU Aero Engines, München, Germany

D. Sporer

Neomet Ltd. / Sulzer Metco, Sonthofen, Germany

Abstract

The efficiency of gas turbines is highly dependent upon the clearance between compressor housing and rotating blades. Abradable seal coatings are employed to minimize the clearance and control the over-tip leakage by allowing the blade tips to cut into the coating and herewith implementing a method of self-adjustment. These coatings consist of a thermally sprayed multiphase material, comprising a metal matrix, a dislocator and a defined level of porosity. Thermally sprayed abradable linings aim at a well balanced profile of properties relevant for the application as abradable seals. Amongst others these include: abradability, ageing resistance, corrosion and oxidation resistance as well as surface finish and bond strength to substrate materials. Due to the high demands in aircraft industry, the coating properties also have to match strict requirements with regards to quality control. Hence the spraying process has to be stable and well controlled. In this work, an APS sprayed abradable coating was sprayed with different sets of parameters and analysed by an on-line diagnostic system. The coating microstructure and properties were evaluated and related to the diagnostic results.

Introduction

Increasing mileage in air transportation along with increasing requirements concerning environmental aspects make high demands on the efficiency of modern jet engines. To meet these requirements, many efforts in optimizing engine lay out design have been made, leading to benefits such as optimized aerodynamic design and higher bypass ratios. Beyond these constructive improvements, only minimum flow losses from engine intake to nozzle outlet, including the rotating compressor as well as turbine stages, are acceptable. Reduction of leakage by improved sealing can result in significantly improved efficiency as well as power output, time-on-wing and compressor stall margin [1-4]. Due to manufacturing tolerances on the one hand and in-service behaviour of rotor blades on the other, reducing the over-tip leakage has been a challenging task in recent years. A promising way to solve this problem is the use of abradable

linings between housing and rotating blades, that allow a self-regulation of the system by a purposeful cutting of the blade tips into the relatively soft coating. The blade wear during that process has to be kept to a minimum, while at the same time the abradable seal coating has to withstand erosive wear due to the particle laden jet and ageing and / or oxidation during service. To meet these demanding requirements, complex thermally sprayed material and coating systems have been introduced to the market and successfully used. Typically they comprise a metal matrix material together with either a solid lubricant or a significant level of porosity to allow cutting of the blade tips with minimum blade wear. Figure 1 shows a typical cross section of an abradable coating based on a NiCrAl/Bentonite material system. The very porous microstructure with bentonite embedded in a NiCrAl metal matrix is clearly observable.

Control of Coating Properties of Abradable Seals by On-Line Process Diagnostics

Figure 1: Cross section of a typical abradable coating

(dark phase: porosity, grey phase: bentonite, bright phase: NiCrAl metal matrix)

The choice of the metal matrix material is mainly depending on the in-service temperature level and blade material the coating has to face. Common and commercially available material systems are e.g. Ni/Graphite and AlSi/hBN [1] for compressor and CoNiCrAlY/hBN/Polyester for turbine sections of aircraft jet engines (Figure 2).

第1页

你可能喜欢

热门文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email