第十五届中国海洋(岸)工程学术讨论会论文集
197
The hydrodynamic performance prediction of ship
hull with propeller and rudder
SHEN Hai-long,GOMRI Abdelhak,QIN Zai-bai,SU Yu-min,PANG Yong-jie
(National Key Laboratory of Science and Technology on Autonomous Underwater Vehicle, Harbin
Engineering University, Harbin 150001, China)
Abstract:In the present study, we conducted ship’s resistance and propulsion performance, using computational fluid dynamics techniques, where a Reynolds-averaged-Navier-Stokes equations (RANSEs) solver was employed. The principal aim of the study is to verify the ability of a CFD method, to predict the hydrodynamic performances of a ship hull appended by propeller and rudder. The complexity in the mesh generation is one of the main obstacles for CFD. For convenience of mesh generation, unstructured meshes were used in the region around ship hull, propeller, and rudder, where the domain's shape is formed of delicate curved surfaces. On the other hand, structured meshes were generated for the rest of the domain. Following a hybrid mesh generation approach, prismatic cells have been generated in the boundary layer, where viscous phenomena are dominant,and tetrahedral cells in the remaining regions. The SST k-w model has been employed for turbulence closure using the steady-rotating reference frame source terms. Thrust and torque forces, pressure and velocity distributions were used to analyze the computed flow field. The hydrodynamic performance prediction method was gotten and was validated. The computational results were validated by comparing with the existing experimental data.
Key words: computational fluid dynamics; turbulence model; mesh; interaction of ship with propeller and rudder; resistance
oefficient
1 Introduction
The flow past a ship hull with propeller and rudder is one of the most challenging problems in the computational fluid dynamics. Various numerical simulation approaches (boundary elements, panel methods, etc.) for studying ship, propeller, and rudder geometries, have been used for decades, but only recently, due to the rapid advances in computer power and in the parallelization capabilities, different CFD methods, and in particular RANS equation solvers, are increasingly applied to simulate the full three-dimensional viscous and turbulent flow for various ship geometries [1, 2].
In the last few years, computational analysis of ship resistance and propulsion using CFD is being widely adopted. The results are being applied to actual design of ships [3-6]. In those applications, however, the difficulty in mesh generation is the most serious obstacle for non-expert users for utilizing CFD with maximum efficiency. In case of mesh generation around a ship hull, the bow and stern regions require special care and experience because of the delicate and rapidly changing surfaces. Therefore, a hybrid meshing approach using unstructured meshing near the complex geometry and structured meshing in the remaining simple geometry domain was suggested[7]. The use of unstructured mesh is suitable for improvement of accuracy and for future extension to complex flows, and for investigation of the hull-propeller-rudder interaction [8-10].
In the present study, we have focused on the hydrodynamic performance prediction of the interaction hull-propeller-rudder using hybrid meshing. The present computational results were investigated through comparison with the experimental data from Shanghai Merchant Ship Design & Research Institute [11].
2 Computational Model and Numerical Techniques
The ship model test for the 57 000 t bulk-cargo ship, named SM0637-1, was carried out in China Ship Scientific Research Center. The design propeller model is named TM0782. The principal particulars for the ship and propeller are described in reference [11]. The shapes of the propeller and stern of ship hull shows in Fig. 1.
The commercial CFD software FLUENT version 6.3 is utilized for the computations in the present study. FLUENT solves the RANS equations with a finite-volume approach on hybrid unstructured grids. A variety of pressure-based algorithms are available in FLUENT. For the present steady-state computations, the SIMPLE algorithm is adopted. The difference schemes of convection terms in the momentum transport and pressure-velocity coupling used for discretizing the equations are discussed. The SST k-w model with wall functions is used for turbulence modeling. The resulting system of equations is solved using an algebraic multigrid method for faster convergence.
PREDICTION OF LOADING DISTRIBUTION AND HYDRODYNAMIC MEASUREMENTS FOR PROPELLER BLADES IN A RIM D_专业资料。Avlbeolea’Isicdic.om ail ni t an,cenertec一...
Propeller Operating in Non-Uniform Flows 噎噎噎噎...the Cabin of Underwater Vehicle 噎噎噎噎噎噎噎...Hydrodynamic Performance Prediction of KaMeWa 125SII...
Propeller-Hull Interaction-Wake iWake field ...Prediction of performance in service 5. ...They have the hydrodynamic advantage of recovering ...
the ship hydrodynamic performance in a berthing ...the hydrodynamic forces acting on the hull, with...Accurate prediction of the time history of the ...
A Potential Based Panel Method for Prediction of Steady and Unsteady ...solving the hydrodynamic performance of the fore propeller and the aft one....
? Fully integrated with hull and outfitting design...the prediction of the hydrodynamic performance of ...Propeller optimisation. ? Resistance calculations. ?...
The prediction of the mini-AUV hydrodynamic performance in complex oceanic ...conducted experimental study on the forces and moments on AUV hull form in...
PREDICTION OF PODDED PROPELLER CAVITATION USING AN UNSTEADY SURFACE PANEL METHOD_专业资料。709 Avibeolea、^^sineic.oall ni t^n,cecdrtm ann.ec Siner...
results with the numerical prediction of unsteady...RANS simulations of propeller in ship hull wakes ...(2004). ‘On the hydrodynamic design of podded ...
For the hydrodynamic research of catamaran and ...the region of high-performance multi-hull ship. ...By calculating the resistance prediction of multi-...
热门文档