CAV2001:sessionB7.005
1
EXPERIMENTAL AND NUMERICAL STUDIES ON A CENTRIFUGAL PUMP
WITH 2D-CURVED BLADES IN CAVITATING CONDITION
M. HOFMANN, B. STOFFEL
Laboratory for Turbomachinery and Fluid Power, Darmstadt University of Technology, Germany
O. COUTIER-DELGOSHA, R. FORTES-PATELLA, JL. REBOUD(*)
Laboratoire des Ecoulements Géophysiques et Industriels, Grenoble, France (*) LTDS/ENISE, Saint Etienne, France
Abstract
In the presented study a special test-pump with 2D curvature blade geometry in cavitating and non-cavitating conditions was investigated using different experimental techniques and a 3D numerical model of cavitating flows. Experimental and numerical results concerning pump characteristics and performance breakdown were compared at different flow conditions. Appearing types of cavitation and the spatial distribution of vapour structures within the runner were also analysed.
1. Introduction
In the scope of the European Research Program PROCOPE, researchers of the TUD (Laboratory for Turbomachinery and Fluid Power at Darmstadt) and of the LEGI (Laboratoire des Ecoulements Géophysiques et Industriels de Grenoble) work together in order to improve the understanding of the unsteady behaviour of cavitating flows and the related erosive aggressiveness.
In order to extend previous analyses concerning the cavitating flows around a 2D-hydrofoil [Hofmann et al., 1999] and in a cascade of three hydrofoils [Lohrberg et al., 2001], the present study consists of investigations by experimental means and numerical simulation concerning a special centrifugal test-pump in cavitating and non-cavitating conditions. Experiments were carried out at Darmstadt University of Technology using different experimental techniques. The measurement of classical pump characteristics and performance breakdown at different flow conditions were associated with flows visualisations. Appearing types of cavitation and the spatial distribution of vapour structures within the runner were analysed.
Three-dimensional Navier-Stokes codes taking into account the cavitation process have been developed during the last years [Takasugi et al., 1993, Alajbegovic et al., 1999, Kunz et al., 1999, Bunnel and Heister, 2000] based on different multi-phase flow approaches [Delannoy and Kueny, 1990, Kubota et al. 1992]. Industrial CFD codes are now starting to take into account cavitation models, allowing first applications to pump geometries [Combes and Archer, 2000]. In this context, a numerical model for three-dimensional cavitating flows is developed at LEGI, based on the 3D code FINE/TURBOTM, developed by NUMECA International. That work is performed in cooperation with SNECMA Moteurs and the French space agency CNES, with the final objective to provide accurate simulations of unsteady cavitating flows in the inducers of rocket engine turbo-pumps [Coutier-Delgosha et al. 2001a,b]. The application to the centrifugal pump represents a first step of validation of the model on steady-state cavitating flow in turbomachinery.
2. Geometry
A special runner geometry has been chosen to easily adapt existing measuring techniques for a single hydrofoil in a test section [Hofmann et al., 1999, Hofmann, 2001] to a pump test-rig. Optical access in 2 planes was made possible to enable a view perpendicular to the blade surface on both suction and pressure side by Plexiglas windows in the housing and a Plexiglas shroud. The runner has 5 single-curved blades with two different radii at inlet and outlet. The part of the blade with the larger radius (the second part in flow direction) was also made of Plexiglas to obtain optical access to the pressure side of the following blade and the entire channel respectively.
Figure 1a shows the intersection of the 2 blade radii. Another characteristic is the parallel hub and shroud to get an almost 2-dimensional blade-to-blade channel with constant width.
A radial-symmetric housing (Figure 1b) is used to obtain almost constant conditions on the runner outlet (if we neglect gravitational forces which are small compared to the performance of the runner). With these preconditions we obtain comparable cavitation conditions in each channel without the influence of a volute casing.
The experimental and numerical studies in a centrifugal pump with two-dimensional curvature blade in cavitation condition based on the Baldwin-Lomax turbulence...
Influence of Blade Wrap Angle on Centrifugal Pump Performance by Numerical and Experimental Study_天文/地理_自然科学_专业资料。CHINESE JOURNAL OF MECHANICAL ...
Centrifugal_Pump_机械/仪表_工程科技_专业资料。Centrifugal_Pump,离心泵性能曲线测定,德国某大学教材今日推荐 180份文档 2014证券从业资格考试...
numerical calculation and most of the studies ... like academic analysis and experimental research, ...a large eddy simulation of a centrifugal pump at...
4 船舶辅机?第3章 离心泵 [Centrifugal Pump] 2. 压出室 作用:以最小的水力损失汇聚从叶轮中流出的高速液体, 将液体引向泵的出口或下一级,并使液体流速降低,...
The accuracy of numerical simulation was validated through the experimental studies on the prototype pump. Key words: centrifugal pump; cavitation inception; ...
31页 5财富值 Numerical Simulation of ... 5页 2财富值 Lab 离心泵 ... 第三章 离心泵 centrifugal pump第三章 离心泵 centrifugal pump隐藏>> 第五节...
Performance Characteristics of Centrifugal Pump ...experimental results on single stage centrifugal ...discussed numerical model o f flow liquid and ...
and Numerical Simulation of a Centrifugal Pump ... while the studies of the transient behavior of ...—numerical simulation based on experimental results...
Numerical Simulation of ... 5页 2财富值 Lab 离心泵 Determination... ...第3章 离心泵 [Centrifugal Pump] 一、相似条件 1. 几何相似:两泵对应的尺寸...
热门文档