无损检测
EN 13445-5:2002 (E)
Issue 7(2003-07)
1 Scope
This Part of this European Standard specifies the inspection and testing of individual and serially producedpressure vessels made of steels in accordance with EN 13445-2 subject to predominantly non_cyclic operation (i.e.vessels operating below 500 full equivalent pressure cycles).
Special provisions for cyclic operation are given in EN 13445-3 and in Annex G of this Part.
This Part does not give inspection and testing provisions for vessels designed using Design by Analysis – DirectRoute (DBA) of EN 13445-3:2002 Annex B.
NOTEThe responsibilities of parties involved in the conformity assessment procedures are given in Directive 97/23/EC.Guidance on this can be found in CR 13445-7.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).
EN 287-1:1992, Approval testing of welders — Fusion welding — Part 1: Steels.
EN 473:2000, Non-destructive testing — Qualification and certification of NDT personnel — General principles.EN 571-1:1997, Non-destructive testing — Penetrant testing — Part 1: General principles.prEN 764-6:2002, Pressure equipment — Part 6: Operating instructions.
EN 583-4:1999, Non-destructive testing — Ultrasonic examination — Part 4: Examination for discontinuitiesperpendicular to the surface
EN 970:1997, Non-destructive examination of fusion welds — Visual examination.
EN 1289:1998, Non-destructive examination of welds — Penetrant testing of welds — Acceptance levels.EN 1290:1998, Non-destructive examination of welds — Magnetic particle examination of welds.
EN 1291:1998, Non-destructive examination of welds — Magnetic particle testing of welds — Acceptance levels.EN 1418:1997, Welding personnel — Approval testing of welding operators for fusion welding and resistance weldsetters for fully mechanized and automatic welding of metallic materials.
EN 1435:1997, Non-destructive examination of welds — Radiographic examination of welded joints.
EN 1712:1997, Non-destructive examination of welds — Ultrasonic examination of welded joints — Acceptancelevels.
5
欧盟压力容器标准EN13445分析设计标准概述定稿_机械/仪表_工程科技_专业资料。化工设备方面资料欧盟压力容器标准EN13445分析设 计标准概述苏文献 上海理工大学化工过程...
浙江 杭州 310027 ; 21 浙江省特种设备检验中心 , 浙江 杭州 310020) 摘 :2002 年 5 月颁布的 EN13445 欧盟 要 《非直接接触火焰压力容器》 标准满足承压...
欧盟压力容器标准EN13445经济性特点的分析_专业资料。欧盟压力容器标准EN13445经济性特点的分析技术综述 欧盟压力容器标准 EN13445 经济性特点的分析姚华堂 , 王正东...
欧盟标准EN13445简介及其与我国压力容器标准的比较_机械/仪表_工程科技_专业资料。我国也EU压力容器标准的分析与比较!维普资讯 http://www.cqvip.com 欧 盟标准...
欧盟压力容器标准EN13445经... 5页 2财富值 欧盟压力容器标准EN13445分......压力 容器》 4章 对钢 板、管、件、栓 第钢锻螺 及螺 母等压力 容器 用...
BS EN 13445-5:2009 EN 13445-5:2009 (E) Issue 1 (2009-07) Figure 6.6.2-3 — Type of welds 26 BS EN 13445-5:2009 EN 13445-5:2009 (E) ...
压力容器国内外常用标准_工学_高等教育_教育专区。对于“标准”的解释,古语有...6.2 欧盟 《非直接受火压力容器 EN13445-2002》 它是一套年轻、先进而又完整...
2. 欧盟压力容器规范名称为 EN13445-2002非直接着火压力容器 ___。 2 第一章...美国压力容器设计规范中的常规设计在 ASME锅炉与压力容器设计规范第___ VIII ...
目前世界上主要的压力容器体系有两种:一是 ASME 标准,二是 欧盟 PED 压力容器...EN 13445: 2002 是强制性法规压力设备指令 (PED, 93/27EC, 1999-11-29 ...
EN压力容器标准与 ASME标准和我国 标准的对比– 基于公式的设计和疲劳设计秦叔经 2006.8 ? EN13445的地位 ? 可不做任何修改而成为欧盟成员国的国家标准 ? ...
热门文档