德国工业标准
DEUTSCHE NORMAugust 1998
Rough castings of grey cast iron
General tolerances and machining allowances
(For replacement purposes only)
{
1686-1
Supersedes
October 1980 edition.
ICS77.140.80
Descriptors:General tolerances, machining allowances, castings, cast iron.Gußrohteile aus Gußeisen mit Lamellengraphit – Allgemeintoleranzen,Bearbeitungszugaben (Nicht für Neukonstruktionen)
In keeping with current practice in standards published by the International Organization for Standardization(ISO), a comma has been used throughout as the decimal marker.
Dimensions in mm
1Scope and field of application
This standard specifies general tolerances and machining allowances for rough castings of grey cast ironwhich are subject to the technical delivery conditions laid down in DIN 1691.
Users of this standard should note that it now only applies to castings used for repair and replacementpurposes. New designs are covered by ISO 8062 : 1994.
Owing to the lack of empirical data, general tolerances have not been specified here for angular dimensions.If angles are to meet accuracy requirements, these shall be indicated as individual tolerances.
2Normative references
This standard incorporates, by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text, and the titles of the publications arelisted below. For dated references, subsequent amendments to or revisions of any of these publicationsapply to this standard only when incorporated in it by amendment or revision. For undated references, thelatest edition of the publication referred to applies.DIN 1680-1DIN 1691DIN 7182-1
ISO 8062 : 1994
Rough castings – General tolerances and machining allowances – GeneralGrey cast iron – Properties
Sizes, deviations, tolerances and fits – Basic concepts
Castings – System of dimensional tolerances and machining allowances
3Concepts
See DIN 7182-1 and DIN 1680-1 for the terms ‘general tolerances’ and ‘tolerance grade’, and DIN 1680-1for a definition of ‘machining allowance’.
4
4.1
Tolerance grades
Dimensional deviations
For castings of grey cast iron, dimensional deviations are largely dependent on
a)the dimensional accuracy of the pattern, the degree of shrinkage dependent on the material type andcasting configuration, the care taken during moulding and casting, and the moulding and casting equip-ment used based on the batch size;b)the nominal sizes.
Continued on pages 2 to 4.
Translation by DIN-Sprachendienst.
In case of doubt, the German-language original should be consulted as the authoritative text.
©No part of this translation may be reproduced without the prior permission ofDIN Deutsches Institut für Normung e.V., Berlin.
Beuth Verlag GmbH, D-10772Berlin, has the exclusive right of sale for German Standards (DIN-Normen).
Ref.No.DIN1686-1:1998-08
English price group06
Sales No.0106
11.98
DIN 1686-1-1998片状石墨铸... 4页 10财富值 DIN 1684-1-1998 可锻铁的... DIN 1685-1-1998 球墨铸铁毛坯一般公差及加工余量 不适于新结构 球磨铸铁一般...
DIN 1685-1-1998球墨铸铁毛... DIN 1686-1-1998片状石墨铸... DIN 1688...1688-1-1998轻金属合金的铸件毛坯.砂模铸造.一般公差及加工余量.不适于新结构...
DIN 1686-1灰铸铁件 一般公差 加工余量_机械/... DIN 1686 CN 01 石墨铸件... 暂无评价 6页 ... DIN 1686-1-1998 片状石... 4页 4下载券 DIN...
DIN 1686-1:1998-08 灰铸... 3页 免费 DIN1688 Part1.3.4 12页 免费... -1 轻金属合金的铸件毛坯[1].砂模铸造.一般公差及加工余量.不适于新结构 ...
DIN 1685-1-1998球墨铸铁毛... DIN 1686-1-1998片状石墨铸... DIN 1688... DIN 1688-3-1980轻金属合金的铸件毛坯.金属模铸造.一般公差及加工余量DIN ...
DIN1686-1-1998 片状石墨铸铁毛坯.一般公差及加工余量.不适于新结构.pdf DIN16867-1982 化工管道用玻璃纤维聚酯树脂管.异型件和接头.交货技术条件.pdf DIN16868-1...
DIN 1686-1:1998-08 灰铸... 3页 免费 DIN1688 Part1.3.4 12页 免费... -1 轻金属合金的铸件毛坯[1].砂模铸造.一般公差及加工余量.不适于新结构 ...
热门文档