(UNSW). His current research interests are in modeling, quality control, algorithm and software development for precise positioning using GPS, Glonass, pseudolites and INS. He holds a Ph.D. from the Curtin University of Technology, Australia, and has autho
y22ij+z xijyij xijzij 2
1 ij
xxdij=d3 xijyijx2
2
ij+zij
y
ijzij (8)ij xijzij
yijzij
x2+y2
ijij
with the extreme eigenvalues being λmin=0 and
λmax=1/dij. From equation (6), the bounds for thenonliearity error caused by ignoring the remainder termR are:
2
220≤R≤
x2=δxij
+δyij
+δzij
2dij
2d
(9)
ij
In integrated GPS-pseudolite attitude determination, thelength of the distances for linearization may vary from20000km between GPS satellites and user, 200m betweenpseudolites and user, and 2m between antennas. Figures1, 2 and 3 show the linearization error bounds for these

three different lengths.
Fig. 1: Linearization error for the distance between

satellites and user (about 20000km).
Fig. 2: Linearization error for the distance between

pseudolites and user (200m).
Fig. 3: Linearization error for the distance between
antennas on the platform (2m).For distances such as between GPS satellites and users onthe ground, the linearization error for a 200m error in thecoordinates is just 1mm, which is clearly negligible. Ithas been shown in Beutler et al. (1988) that the modelerrors caused by errors in the reference station coordinatesis inversely propositional to the satellite/user distances.For the short baselines, as used in GPS attitudedetermination, accurate coordinates for the two end pointsof the baselines are not necessary. This is why the GPSattitude determination system can work without the needfor a stationary reference station.
However, when the separation between pseudolites andusers is 200m, an error of 15m in coordinates may resultin a linearization error of as much as 0.6m, which is muchlarger than the phase measurement errors and may lead todivergence of the computation process. Specialtechniques have to be considered to mitigate against largelinearization errors (Elrod & Van Dierendonck, 1996).In integrated GPS-pseudolite positioning, a stationaryreference station is set up to obtain differential pseudo-range solutions, which provide initial coordinates ofsufficient accuracy. The precise relative positionsbetween the pseudolites and the reference stations arerequired. Nevertheless, a stationary reference station isalso necessary for the precise determination of platformpositions, which, together with the attitude parameters, areimportant information for control and navigationapplications.
In ambiguity resolution it will be desirable to use theknown baseline lengths as constraint. In literature, thebaseline length constraint is usually used in its quadraticform to help reduce the ambiguity search space. Intheory, this kind of information could also be explicitlyused in ambiguity-float solutions, which will enhance thegeometry and lead to improved solutions. However, asshown in Figure 3, due to the relatively short lengths ofsuch baselines, small errors in the coordinates will resultin significant linearization errors. If the baseline lengthsare ‘fixed’ to their known values, the linearization errorswill bias the solutions. This situation could be eased if theknown baseline lengths are treated as ‘measurements’.The accuracy of such measurements should be properly
of the International Association of Geodesy (IAG) Special Study Group (SSG)...He is a member of the Editorial Advisory Board of the journal GPS ...
Shaowei is Chairman of the International Association of Geodesy (IAG) Special Study Group (SSG) 1.179 "Wide Area Modelling for Precise Satellite ...
Solutions, and Chairman of the study group on pseudolite applications in positioning and navigation within the International Association of Geodesy's Commission...
Chairman of the IAG's Special Study Group 1.179 Wide November 1998. ...multiple reference stations, International Association of Geodesy Symposia, vol....
He is Chairman of the Working Group "Pseudolite ...the International Association of Geodesy's Special ...In this study, we apply a method based on ...
study of engineering structures; and Maintain links...of the International Association of Geodesy (IAG) ...Working Group 6.2, Special Equipment for ...
例如,与 GRS75(Geodetic Reference System, GRS75)托球体, recommended by the International Association of Geodesy (IAG)比较,Krassovsky的长半轴比GRS75长了约...
The IGS is an approved service of the International Association of Geodesy since 1994 and is recognized as a member of the Federation of Astronomical and...
The International Association of Geodesy (IAG) ...? The study of the natural and social ... has a special position and role as a promoter...
(GRS80) Adopted by the International Association of Geodesy (IAG) during the General Assembly 1979 equatorial radius of the Earth a 6378137 m f:=1 : ...
热门文档