286Chin. J. Chem. Eng., Vol. 19, No. 2, April 2011
cylinder, which was connected with a capillary. En-trapping air in the capillary was excluded before the dilatometer was immersed in a constant temperature bath. Liquid level in the capillary increased because of the thermal expansion. Then the liquid level stopped rising and kept at an equilibrium state. When the liq-uid level began to fall, volume changes in the capillary were immediately monitored at each 5 min until the end of the experiments, i.e., the liquids level reached the bottom of the capillary. Experimental conditions for the crosslink polymerization kinetic study of AA/AMPS hydrogels are summarized in Table 1.
Table 1 Summary of experimental conditions for the
crosslink polymerization kinetic study of
AA/AMPS hydrogels
Crosslinker①
/%
AA /mol·L 1
AMPS /mol·L 1
Initiator /%
T /°C
zation rate constant, [I] is the initiator concentration, [M] is the monomer concentration, x and n denote the reaction order of initiator and total reaction order, re-spectively. Here, the reaction order considered is the total reaction order, the reaction order of monomers, and the reaction order of initiator.
3.1.1 Total reaction order
Single factor analysis was applied to determine the reaction order of monomers AA and AMPS. When the initiator keeps at a constant concentration, Eq. (1) is simplified as
Rp= d[M]/dt=K[M]n (2)
where K is the apparent polymerization rate constant. The integral equation of Eq. (2) is
ln[M]/[M0]= Kt(n=1)[M]( n+1) [M0]( n+1)=Kt(n 1)
(3)
0 5.6 0.6 0.5 45
where 0.8 6.9 0.3 1.0 50
n=1 refers to the first-order reaction while
n=2 refers to the second-order reaction. The residual 1.2 1.5 55
monomer concentration after reaction time t is calcu- 2.0 60
lated by
65
① The amount of crosslinker or initiator is mass percent (%) of
[M]=[M0](1 V/Va) (4)
total monomers mass.
2.3 Fourier transfer infrared (FTIR) spectroscopy
measurements
To prepare dried gel samples for FTIR measure-ments, monomers AA and AMPS were dissolved in aqueous solution (20 ml), followed by addition of ini-tiator sodium persulfate and crosslinker N,N′-methylene bis(acrylamide). The mixture was well stirred and transferred into a plastic pipe (diameter: 6 mm; length: 20 cm) and put in a constant temperature water bath of 50 °C for 2 h to produce AA/AMPS hydrogel. After the hydrogel was synthesised, it was immersed into deionized water for three days, with changing the wa-ter twice a day to eliminate unreacted monomers and linear polymer chains. Finally, the swollen hydrogel was put into a vacuum oven for 12 h and the dried gel was ready for use in the spectrum test. FTIR spectrum was obtained by using FTIR 2000 with KBr pellets containing dried AA/AMPS hydrogel. The scanning range was 500-4000 cm 1 and the resolving capability was 4 cm 1.
3 RESULTS AND DISCUSSION
3.1 Kinetic equation of the crosslink polymerization For binary radical copolymerization, the kinetic equation is given by
Rp= d[M]/dt=k[I]x[M]n (1)
where Rp is the polymerization rate, k is the polymeri-
where [M0] is the initial monomer concentration, V is the volume change of the system after polymerization time t, Va is the volume change of the system during the whole polymerization. Replacing the monomer concentration [M] in Eq. (3) with Eq. (4), we obtain
ln(1 V/Va)= Kt(n=1)
(1 V/Va)( n+1)=1+
Kt(n 1) (5) [M0]( n+1)
There is a relationship between the volume change of the polymerization mixture and the mono-mer conversion rate. This volume change can be ob-tained by using dilatometry and V value is closely related to the liquid level change in the capillary
V=A(h0 ht)=A h (6)
where h0 and ht denote the liquid level height in the capillary at the beginning and at time t of the polym-erization, respectively, h is the height change of liq-uid level, and A is the cross-sectional area of the cap-illary. Replacing V in Eq. (5) with Eq. (6), we have
h A ln 1 = Kt(n=1)Va
(7)
Va111 =1+ (n=2)A hK[M0]t
Va value is often viewed as a constant as it is calcu-lated by
Va=V0(1 dM/dP) (8)
where dM and dP are the monomer and polymer densi-ties, respectively, at certain temperature, and V0 is the
AA_AMPS水凝胶的交联聚合反应动力学及其机理_英文_ 隐藏>> CATALYSIS, KINETICS AND REACTORS Chinese Journal of Chemical Engineering, 19(2) 285—291 (2011) ...
研究了采用溶液聚合法制备的 AA/AMPS 共聚物 Poly(AA-co-AMPS)水凝胶的吸液性能,结果表明: 合成的凝胶材料在 0.9%生理盐水中的吸液能力达到 125 g/g 以上;...
AA/AMPS共聚物水凝胶的吸液性能_专业资料。研究了采用溶液聚合法制备的AA/AMPS共聚物Poly(AA-co-AMPS)水凝胶的吸液性能,结果表明:合成的凝胶材料在0.9%生理盐水中...
西南石油大学油气藏地质及开发国家重点实验室 ,四川 成都 610500) 摘要 : 采用...AA_AM_AMPS超浓反相乳液... 5页 免费 AA_AMPS水凝胶的交联聚合... 暂无评价...
5页 免费 AA、AM和AMPS聚合物的研究... 3页 1财富值喜欢此文档的还喜欢 水...1 文献标识码: A 高分子凝胶是由交联高分子网络、 溶胀溶剂 等组成的多元体系...
( AMPS) 及非离子型单体甲基丙烯酸丁酯为原料,偶氮...( AA) 、 N - 亚甲基双丙烯酰胺 丙烯酰胺( AM...聚合物交联聚合物交联制备水凝胶有化学交联 、 物理...
P_AAEA_AMPS_AA_超大孔水凝胶的制备及性能_王立华...或支链含有大量亲水性基团并遇 水膨胀的交联聚合物...英文个人简历模板 创意简历模板汇集 推理型题分析与总结...
丙烯酰胺 (M)A与 VP共聚物水凝胶可用于蛋白 CO—AA)含物中引人温敏性聚合物...二醇双 H为乙 甲基 丙烯酸酯(GEDMA)交联剂合成共聚物水凝 为 胶的动力学 规律...
pH敏感性P(AAm-co-AA)半... 5页 2下载券 pH...历史的共聚及均聚水凝胶的溶胀皆符合二级动力学机理...交联剂配比与 #R " 相同, 聚合反应前加入 "%% ...
从 Schif f 碱反应机理, 结合红外光谱分析, 提出甲醛交联壳聚糖的交联键结构。 [ 关键词] 甲壳素; 壳聚糖; 交联改性; 保水凝胶 [ 文章编号] 1000- 8144(...
热门文档