文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 能源/化工 > 孔口板及取压法兰
侵权投诉

孔口板及取压法兰

孔口板外型尺寸及取压法兰介绍

Orifice Plate and Flange Specifications ZW07 Series

Orifice plate is a differential pressure type primary device used to produce a fluid flow restriction in a pipeline. The differential pressure across the orifice plate is proportional to the square of the fluid velocity. Orifice plates are best used in clean non-viscous fluids. The most common primary flow element is the concentric paddle type orifice plate in combination with flange union. The main advantages are: low cost, ease of installation, accuracy, variety of construction materials, and quick delivery.

ZW orifice plates are precision bored to exact dimensions with a sharp upstream edge to assure accuracy. Orifice plates are correctly finished to the dimensions, surface roughness and flatness to the applicable standard. Orifice information (Tag No., Pipe I.D. Orifice Diameter, Flange Rating, Plate Material) are stamped on the upstream side of paddle.

Standard Specifications Orifice plates are manufactured in strict accordance to ISA, AGA, ASME and ISO standards. T ype of bore°GSharp edged concentric orifice Rangeability°G4 to 1 T ypical accuracy°G°”2~4% of full scale Nominal pipe sizes°G1/2" to 24" Flange rating°GANSI 150, 300, 600, 900, 1500LB RF JIS 10, 20, 30K RF Plate thickness°G1/8", 1/4" Plate material°G304SS, 316SS and other materials are available Pressure taps°GFlange taps, D& 1/2D taps, Pipe taps and Vena contracta taps Drain and vent hole°GISA-RP3.2 recommendations. Not drilled for orifice bore smaller than 25.4mm Bore tolerance in strict accordance with A.G.A Gas Measurement Committee Report No. 3, A.S.M.E. Fluid Meters Committee Report, and with other Societies recommendations.

May, 2007 1

Data Sheet/ ZW07-01

孔口板及取压法兰

孔口板及取压法兰

第1页

你可能喜欢

热门文档

相关文档

  • 标准孔板取压法兰结构尺寸

    标准孔板取压法兰结构尺寸_机械/仪表_工程科技_专业资料。开封泰诺仪表有限公司 标准孔板取压法兰结构尺寸 1、角接取压: 角接取压包括环室取压和单独钻孔取压...

  • 孔板取压方式总结

    孔板取压方式孔板应该是分为角接取压 (包括环室取压、 钻孔取压) 、 法兰取压、 径距取压 (D-1/2D 取压) 三种。 节流件形式表示方法 :代号 F H Z...

  • 理论取压法取得的差压一般比径距取压大点

    但是法兰取压最 常见,实现容易 一般情况下,法兰取压和径距取压用得比较多,而角接取压的情况下,往往采用内藏孔板;法兰取压采用专用法 兰,B16.36 标准 什么...

  • 流量计的取压方式

    压损比较 压损比较 V 锥压损 孔板的压损 B=0.35 85%×DP B=0.45 74...法兰连接 式 取压方式:1/4“~1/2”NPT 螺纹取压(配一次阀门) 法兰、外...

  • 法兰安装检查以及流量孔板安装检查纪要

    管道法兰及流量力矩值要求的讨论纪要法兰是使管子与管子相互连接的零件, 连接于... 孔板流量计的安装要求 2页 1下载券 标准孔板取压法兰结构尺... 暂无评价 ...

  • 板式平焊法兰手孔

    本标准 公称压 P 适用于 力 N小于和等于 。6P、. a工作温度根据材料类别... 其中垫片 采用石棉橡胶板垫的板 式平焊法兰 手孔 , 其规定标记符号 为: 手...

  • ORIFLO_TG-F771-5E

    孔口板及取压法兰 8页 免费 中外阀门常用材料对照表 6页 1下载券 电气安装工程识图教程 40页 1下载券ORIFLO_TG-...

  • 法兰钻孔模板及连接螺栓长度

    【 ˉ 86 -ˉ ˉ 管法兰及法兰管件 药∞ 级法兰 AsRJE B16-Om 双头 及妇母 "梭衣犭 Ⅱ m级 法兰钻孔丧板 公猕曾径 0梭 屮心法兰外径 NPs 0 % 1...

  • 孔板式流量计法兰泄漏分析

    #1 低压供热流量计法兰泄漏分析摘要:标准孔板流量计是测量流量的差压装置,配合各种差压计和差压变送 器可用来测量管道内各流体流量。标准孔板流量计的节流孔板包括...

  • 法兰修复,现场机械加工,镗孔,轴颈加工,螺栓紧固,螺栓拉...

    钻取螺栓 江达扬...板等 适用部位 一、带压密封(堵漏)三通泄漏 法兰...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email