毕业论文心得日记—思想的火花
敏捷诗千首,飘零酒一杯。三山半落青山外,一水中分白鹭洲。人谁无过?过而能改,善莫大焉。他山之石,可以攻玉。只要功夫深,铁杵磨成针。Mold & die components 模具单元
Mold changing systems 换模系统
Mold core 模芯
Mold heaters/chillers 模具加热器/冷却器
Mold polishing/texturing 模具打磨/磨纹
Mold repair 模具维修
Molds 模具
Pressing dies 压模
Quick die change systems 速换模系统
Quick mold change systems 快速换模系统
三、模具
塑料模具mould of plastics
注塑模具injection mould
冲压模具die
模架mould base
定模座板Top clamping plate
Top plate
Fixed clamp plate
水口推板stripper plate
A板A plate
B板B plate
支承板 support plate
方铁 spacer plate
底针板 ejector plate
面针板 ejector retainer plate
回针 Return pin
导柱 Guide pin
有托导套 Shoulder Guide bush
直导套 Straight Guide bush
动模座板Bottom clamp plate
Moving clamp plate
基准线datum line
基准面datum plan
型芯固定板core-retainer plate
凸模固定板punch-retainer plate
顶针ejector pin
单腔模具single cavity mould
多腔模具multi-cavity mould
多浇口multi-gating
浇口gate
缺料starving
排气breathing
光泽gloss
合模力mould clamping force
锁模力mould locking force
挤出extrusion
开裂crack
循环时间cycle time
老化aging
螺杆screw
麻点pit
嵌件insert
活动镶件movable insert
起垩chalking
浇注系统feed system
主流道 sprue
分流道runner
浇口gate
直浇口direct gate , sprue gate
轮辐浇口spoke gate , spider gate
点浇口pin-point gate
测浇口edge gate
潜伏浇口submarine gate , tunnel gate
料穴cold-slug well
浇口套sprue bush
流道板runner plate
排飞槽vent
分型线(面)parting line
定模stationary mould,Fixed mould
动模movable mould, movable half
上模upper mould, upper half
下模lower mould, lower half
型腔cavity
凹模cavity plate,cavity block
拼块split
定位销dowel
定位销孔dowel hole
型芯core
斜销angle pin, finger cam
滑块slide
滑块导板slide guide strip
楔紧块heel block, wedge lock
拉料杆sprue puller
定位环locating ring
冷却通cooling channel
脱模斜度draft
滑动型芯slide core
螺纹型芯threaded core
热流道模具hot-runner mould
绝热流道模insulated runner mould
熔合纹weld line (flow line)
三板式模具three plate mould
脱模ejection
换模腔模具 interchangeable cavity mould
脱模剂release agent
注射能力shot capacity
注射速率injection rate
注射压力injection pressure
差色剂colorant
保压时间holdup time
闭模时间closing time
定型装置sizing system
阴模female mould,cavity block
阳模male mou
模具各零部件名称中英文对照模具各零部件名称中英文对照.txt铁饭碗的真实含义不是在一个地方吃一辈子饭,而是...
模具基本零件 模具基本零件 1:模具零件 模具零件名称中英文对照一览表 零件名称 上固定板 母模板 公模板 模脚 上顶出板 下顶出板 下固定板 隔热板 脱料板 母...
模具零件的中英文标准命名 模具零件的中英文标准命名 前言 类别 标准名称 MOLD 解析与说明 又称模架 码在注塑机定板上, 又称上模固定板 安装热流道板的架板 ...
模具零件名称中英文对照一览表_英语学习_外语学习_教育专区 暂无评价0人阅读0次下载举报文档 模具零件名称中英文对照一览表_英语学习_外语学习_教育专区。模具...
模具零件名称中英文对照上下模座 导柱 导套 导板 导正销 导向腿 导向块 反侧块 凸模 拉延压边圈 上下压料芯 冲孔冲头 球锁 凹模套 修边镶块 空刀 刃...
模具零件标准名称中英文对照表_机械/仪表_工程科技_专业资料。模具零件标准名称中英文对照表 1 顶针E.P. 88 拉杆suppor pin 2 有托顶针stepped E.P. 89 ...
修订:1 次 制定日期:2006-08-23 发行日期:2006-08-24 页次:第 2 页共 10 页 模具零部件名称及中英文对照 2.0 范围: 适用于福帆公司模具及配件统一名称...
模具零部件名称及中英文对照_Ver.F_机械/仪表_工程科技_专业资料。文件编号: 文件编号:yao_1 内容: 模具零部件名称及中英文对照 版本: 版本: F 材料: 材料...
给需要工作中用到英文冲压模具词汇以帮助模具零件名称中英文对照上下模座 导柱 导套...
模具零件中英文对照表_机械/仪表_工程科技_专业资料。模具零件中英文对照表模具零件名称中英文对照一览表零件名称 上固定板 母模板 公模板 模脚 上顶出板 下顶...
热门文档