文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 自然科学 > 天文/地理 > Technique of high accuracy 3D seismic exploration for fracture-cavity type reservoirs
侵权投诉

Technique of high accuracy 3D seismic exploration for fracture-cavity type reservoirs

SEG

Technique of high accuracy 3D seismic exploration for fracture-cavity type reservoirs

Wang Yanfeng*, Yan Feng, Wang Naijian, Gao Guocheng and Zhang Xiangquan, BGP, CNPC

Summary

Fracture-cavity type carbonate reservoirs are widely developed in the northern Tarim basin area and are great exploration prospects. A deep Ordovician carbonate in the western Tarim the most important exploration target, but it is difficult to explore due to its depth and extensive fractures, cavities and caverns. In this paper, we come up with a method to more accurately model this type of reservoir. We apply a quantitative design of the acquisition geometry to obtain a higher S/N ratio and resolution using wave equation forward modeling based on the properties of the reservoir. In order to satisfy the interpretation of fracture-cavity type reservoir, we apply a wider azimuth survey. Finally, we show the high accuracy 3D exploration result that is achieved by using the new method in the northern Tarim basin area.

Introduction

The Ordovician carbonate reservoir in the northern Tarim basin area is buried deeply, and has abundant caverns and fractures. Block A, located on the western slope of the low uplift in Lun-nan is one typical area of this type of reservoir, and its buried depth is more then 6500 m. Seismic data with high S/N ratio, high resolution and high fidelity are needed in order to describe this type reservoir, but most prior explorations in this region were 2D and primarily focused on the Silurian and Carboniferous, thus are not of use for interpreting the Ordovician reservoir. Additionally, the well locations we have determined based on 2D seismic data are failures. Therefore, we should implement 3D exploration in the area urgently.

Recently, many 3D seismic explorations were carried out in northern Tarim basin area, and most of them used smaller bin (20m) and lower fold (32-48), through which we have obtained good results. However, the main target layers of these explorations were Carboniferous in age. The surface in the northern Tarim basin area is relatively simple and the excitation and receiving conditions are not bad, yet we cannot make significant progress using the present equipment. Therefore, designing an acquisition geometry that can target deep layers while offering highly accurate seismic data for interpretation is the main issue for exploration in the northern Tarim basin area. We have obtained the proper geometry for block A in this area based on wave-equation forward modeling and quantitative design. The quality of seismic data was improved significantly, and the well locations we have determined based on the new 3D seismic data are all successful.

© 2010 SEG

Seismic detectability of fracture-cavity Carbonate reservoirs

Fracture-cavity carbonate reservoirs are complex heterogeneous reservoirs and can be considered as non-stratified reservoirs that consist of quasi-homogeneous media with different sizes and shapes, irregular distribution and low velocity. The wave on seismic attributes should be the scattered wave generated by those low velocity reservoirs.

Theoretical studies about deep fracture-cavity carbonate reservoirs (Yao and Tang, 2003) indicate that the detectability of cavity is related to the velocity of surrounding rocks of caverns, the velocity of fluid of caverns, the dominant frequency and the level of background noise. The detectability cannot be determined by using 1/4 wavelength of seismic wave in the surrounding rocks. In the vertical direction, 1/4 wavelength is used to study the resolution of thin beds with reflection interfaces with the usual reflection coefficient (<0.2). This method estimates the limiting resolution of thin beds by using the time difference between wave crest and trough. This limiting resolution is not the limit of identification of reflection of thin beds on the seismic profile. In the horizontal direction, 1/4 wavelength is the limit to determine the width of the cavern by using the length of the short reflection section of migration homing, not the limit of seismic wave. In order for the cavern to be detected, the amplitude of the scattered wave must be stronger than the background noise[1]. During practical seismic exploration, we usually find that the volume of the target calculated by the moniliform on the seismic profile is bigger than the real volume (the theoretical height and width of cavern is more than 1/4 wavelength), which means that even if the height and width of cavern is smaller than 1/4 wavelength, we still can identify the cavern, but the volume is not correct.

Forward modeling for fracture-cavity reservoirs

Forward physical modeling is the most direct way to study the influence of acquisition parameters in fracture-cavity reservoir exploration. We apply wave-equation forward modeling and pre-stack time migration methods to compare different trace interval, fold number and frequency to identify fracture-cavity reservoirs in the northern Tarim basin.

The physical model includes 15m*30m, 20m*40m, 25m*50m, 50m*100m and 75m*150m (height*width) caverns at stake number 8000, 11000, 14000, 17000 and

第1页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email