G Model
JMSY-288;No.ofPages16
G.Gelen,M.Uzam/JournalofManufacturingSystemsxxx(2014)xxx–xxx

5
Table1PLCinputs.
PLCinputs
Sensor
De nition
I0.0I0.1I0.2
Sensor1Sensor2Sensor3
DetectsaringorpegatthesortareaDetectsapegatsortarea
Detectsaringintheassemblyarea
Table2
PLCoutputs.
PLCoutputs
Actuatornumbers
De nition
Sortsolenoid
AssemblysolenoidUpperconveyormotorLowerconveyormotor
Q0.0Q0.1Q0.2Q0.3
Actuator1Actuator2Actuator3Actuator4
Step6canbeperformedbystandardSCTsoftware,thepackage[27]isusedforthiscomputation.Step6canbesummarizedasfollowsforplacesp1,p2,p3,...,pNofUAPNMandbufferrepre-sentationoftheseplacesP1,P2,P3,...,PN
Fig.6.APNmodelofPLANTandsub-plantsPLANT1andPLANT2.
reductiontechniquesinstep3arewellknown,andpreserveprop-ertiessuchasboundedness,liveness,andreversibility.Forstep4,ifplacepisboundedinaccordancewithM(p)≤b,say,thenpismodeledbyabufferwithcapacityb(i.e.b+1states).ForexampleifanAPNplacehasatokencapacityof3,thenitcanberepresentedby4states.Thereaderisreferredto[26]fordetailedinformationaboutthistransformation.
Instep5,APNmodelsofsub-plants(PLANTm)relatedtoeachoneofspeci cationsaredetermined.Todothis,speci cationsareconsideredonebyonewithplantmodelandtherelatedpartofplantAPNmodelisindicated.
6.1Toobtainmodularsupervisor rsttaskistoobtainautomata
modelsofallsubcomponents(P1,P2,...,PN)byusingCreate(.)commandofTCTsoftware.
Pi=Create(Pi)i=1,2,3,...,N
6.2Asasecondtask,eachofthesespeci cationsiscreatedsepa-ratelybyusingCreate(.)command(SPEC1,SPEC2,...,SPECMmisthenumberofspeci cations):
SPECk=Create(SPECk)k=1,2,3,...,m
6.3EachpartofPLANT(subnets)relatedtospeci cationsiscreated
byusingsynchronousproductofplacesthatarecoveredbysubplantmodel.
PLANT1=Px||Py||Pz...PwPLANT2=Px||Py||Pz...Pw...
PLANTM=Px||Py||Pz...Pw
6.4EachoneofmodularsupervisorsisobtainedbyusingSupcon(.)
commandofTCTsoftwareasfollows:
MODSUP1=Supcon(PLANT1,SPEC1)MODSUP2=Supcon(PLANT2,SPEC2)...
MODSUPM=Supcon(PLANTM,SPECM)

t6
t7

a)
b)
Fig.7.(a)APNmodelofPLANT1relatedtothe rstcontrolspeci cationand(b)APNmodelofPLANT2relatedtothesecondcontrolspeci cation.
Hybrid 类型的端口可以属于多个 VLAN,可以接收和发送多个 VLAN 的报文,可以用 于交换机之间连接,也可以用于连接用户的计算机。 其中,Hybrid 端口和 Trunk 端口的...
hybrid 配置实验交换机一台,pc 机若干台,直通网线若干,通过交换机端口的 trunk 功能实现跨交换机之 间的 vlan 互通 1.要求三个 vlan 的 pc 均可以访问 server...
Hybrid Architecture Architectures of HEV Series hybrid Fuel tank IC engine Generator Parallel hybrid Fuel tank IC engine Transmission Transmission Battery Power ...
陈奕男の海报实验室 如何制作一张 Hybrid Image 文 / 陈奕男 转载请注明出处及作者 本文将对如何使用Photoshop实现Hybrid Image进行讨论和研究,并给出如何使用...
交换机 Hybrid 端口配置 一 组网需求: 需求一 1. PC1、 和 PC3 分别连接到二层交换机 SwitchA 的端口 E0/1 、 PC2 E0/2 和 E0/3, 端口分属于 ...
原生App 与 移动Web App 混合app(Hybrid App)那个好_互联网_IT/计算机_专业资料。原生App 与 移动Web App 混合app(Hybrid App)那个好...
? ? ? 移动 HTML 5 Node.js 云计算 大数据 运维 架构师 QCon 大会 QClub LBS 全部话题 New UI 您目前处于:InfoQ 首页文章 Hybrid App 开发实战 Hybrid App...
将希望可以互通的端口的pvid vlan,设置为untagged vlan,这样从该端 口发出的广播帧就可以到达本端口 [Switch-Ethernet0/1]port hybrid vlan 10 40 50 60 ...
Page 5 Hybrid MSTP组网-TDM与分组平面共存 OSN3500/1500/M1000 RNC RNC BSC STM-1/4/ IMA E1/ Native E1 TDM&分组双平面交叉板 STM-16/64 TDM XC ...
华为S23系列hybrid端口删除方法(华为其它系列可做参考) 2012-02-16 21:27:07 分类: 默认分类 标签:华为s23系列 hybrid 端口删除 举报字号 订阅 本人在做...
热门文档