文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > 2007 日本-MEMS-BASED UNCOOLED INFRARED FOCAL PLANE ARRAYS
侵权投诉

2007 日本-MEMS-BASED UNCOOLED INFRARED FOCAL PLANE ARRAYS

mems

and electrical conducting path. If the thermal conductance of the support structure is sufficiently low, a detectable temperature change is generated at the temperature sensor by absorbing infrared rays, and a change in the output from the temperature sensor is read out through a readout circuit on the substrate. Assuming a vacuum condition, temperature change by absorbing infrared energy is inversely proportional to the thermal conductance of the support structure. Since sensitivity is proportional to temperature change, reducing thermal conductance is crucial to enhance sensitivity.

3. MEMS-BASED UNCOOLED IRFPASFigures 2 and 3 show pixel cross-sections of microbolometer and SOI diode uncooled IRFPAs. In the microbolometer pixel, a thin VOx film is deposited on a microbridge structure that is supported by two narrow legs. The typical temperature coefficient of resistance (TCR) of VOx used for uncooled IRFPAs is around 2%/K. Infrared absorption is performed by a 1/4 wavelength resonant cavity, consisting of an infrared reflector on the substrate, infrared absorbing thin metal in the microbridge, and the gap between them. This structure is fabricated by a surface micromachining process in exclusive MEMS process facilities after a standard CMOS process.

The first successful microbolometer uncooled IRFPA was a 240x336 element device with a 50

µm pixel pitch [2]. This uncooled IRFPA exhibited a very high performance of 40 mK NETD with f/1 optics.

The motivation to develop other bolometer materials is to obtain higher TCRs and/or to establish fully Si-compatible production processes. Examples of bolometer materials investigated for uncooled IRFPAs include amorphous Si [8], polycrystalline SiGe [9], YBaCuO [10], and so on. Although some exhibited promising results, VOxcontinues to predominate due to its low 1/f noise and appropriate resistivity.

The SOI diode uncooled IRFPA uses single-crystal pn junction diodes as temperature sensors. A Si pn junction diode driven in a constant current mode has temperature sensitivity of about 2 mV/K in the forward voltage. The diode temperature sensor is held over a cavity by two thin support legs that is made by a XeF2 bulk micromachining process. In contrast to the infrared absorber in the microbolometer pixel, the infrared absorber for the SOI diode is formed at a different level from the diode temperature sensor. This structure enables us to design the infrared absorber as large as possible, without considering the layout of the support legs, which assures nearly 100% fill factor. The infrared absorber and diode temperature sensor are thermally connected with pillars having much higher thermal conductance than the support legs. To fabricate a freestanding infrared absorber, an additional surface micromachining process is needed. Figure 4 is an SEM photograph of 40 µm pitch SOI diode pixels,

2007 日本-MEMS-BASED UNCOOLED INFRARED FOCAL PLANE ARRAYS

The 14th International Conference on Solid-State Sensors, Actuators and Microsystems, Lyon, France, June 10-14, 2007

TRANSDUCERS & EUROSENSORS ’07

Etching Stopper

Buried Oxide

2007 日本-MEMS-BASED UNCOOLED INFRARED FOCAL PLANE ARRAYS

Fig. 3 Pixel structure of SOI diode uncooled IRFPA.

上一页第2页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email