文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 建筑/土木 > Experimental Analysis of Structure and Deformation Mechanisms of Expanded Polystyrene (EPS) Slabs
侵权投诉

Experimental Analysis of Structure and Deformation Mechanisms of Expanded Polystyrene (EPS) Slabs

Durability and stability of polymeric foam products used in building pplication in most cases is associated with compressive strain. The echanical characteristics of such products for the most part depend on the materials structure and density as well as on the applied load value. In this work the analysis of expanded polystyrene slabs (EPS) structure and deformations are provided.

ISSN 1392–1320 MATERIALS SCIENCE (MED IAGOTYRA). Vol. 12, No. 4. 2006

Experimental Analysis of Structure and Deformation Mechanisms of Expanded Polystyrene (EPS) Slabs

Saulius VAITKUS , Antanas LAUKAITIS, Ivanas GNIPAS, Vladislovas KER ULIS, Sigitas V JELIS

VGTU Institute of Thermal Insulation, Linkmenu 28, LT-08217 Vilnius, Lithuania

Received 31 August 2006; accepted 12 October 2006

Durability and stability of polymeric foam products used in building application in most cases is associated with compressive strain. The mechanical characteristics of such products for the most part depend on the materials structure and density as well as on the applied load value. In this work the analysis of expanded polystyrene slabs (EPS) structure and deformations are provided. The influence of the average beads diameter on the density of EPS specimens was estimated. The analysis of the materials structure is revealed through the compressive stress-strain diagram. The analysis of EPS micro and macro structure was carried out at each point where the compressive diagram breaks. The study of the changes that take place between and inside the beads of EPS specimens, when they are under compression, revealed the mechanism EPS deformations.

Keywords: expanded polystyrene slabs (EPS), bead walls, compression, deformations, stress-strain diagram, structure,

spaces between beads.

INTRODUCTION

The EPS products are widely used in many applica-tions. Most often they are used for thermal insulation, packing, structural use and buoyancy [1]. Polymeric thermo insulating materials posses a number of valuable properties such as following: sufficient strength, low density, water absorption, resistance to watering and thermal conductivity. Moreover, these materials are easily processed; they may be molded or cut into unlimited shapes as well as recycled [2, 3]. One of the main features that characterize the material is the density of polymeric thermo insulating material. If the density of the porous material is known, thermal and strength properties of the material may be approximately predicted [4]. However, sometimes it happens vice verse: though the density of the materials is the same but the structure is different, the mechanical characteristics of the material may also differ [5].

The cellular material may be produced using most of the polymer materials, nonetheless, only some of them are used in industrial application [2]. Most widely used polymers are as follow: polyurethane, PVC, polystyrene, polypropylene, epoxy, phenol-formaldehyde, cellulose acetate, silicone, etc [6]. Expanded polystyrene slabs are widely used due to the fact that its manufacturing technology is rather simple and the production costs are rather low [7]. The EPS materials are made out of hard polymeric matrix and gaseous phase. Gaseous phase of expanded polystyrene slabs can take up as many as 98 % of its volume. In the open cell foams gas may navigate through the chanels of matrix, whereas, in the closed cell foams gas navigates only through the walls of cells by diffusion. Gas conduction through matrix is one of the factors that determine physical and mechanical

Corresponding author. Tel.: +370-5-2752485; fax.: +370-5-2752485. E-mail address: saulius.vaitkus@termo.vgtu.lt (S. Vaitkus)

characteristics of cellular plastics. In real cellular plastic both structural types may exist at the same time. The number and size of closed cells are the main structural characteristics of the cellular material because they influence the mechanical characteristics of the porous material, water absorption and thermal properties [2, 3]. The number and size of polymeric thermo insulating materials beads depend on the raw materials used and production process.

Most often expanded polystyrene slabs are manufactured by steam molding: raw polystyrene beads are expanded and then fused together in closed mold. In order to get an evenly porous structure and optimal physical-mechanical characteristics of the material, all the beads in the form must be heated equally and fast. This condition may be reached when optimal parameters of thermal heating using steam regime are set. When the pressure of steam is constant, the amount of heat conducting depends only on the time length of the process [8].

Exploitation of polymeric foam products used in building application in most cases is associated with compressive strain. The compressive strains and collapse of EPS may be revealed through stress-strain diagram [1, 6, 9 – 11]. Different mechanical states of expanded polystyrene slabs are presented in Fig. 1. In this diagram σA indicates the end of stress-strain approximately linear dependence. σB indicates the end of bending deformations process in cell walls, which causes the walls to lose stability. If σB is exceeded, the elements of structure are damaged, and the densification of the material starts.

The aim of this work is to evaluate the relationship between the expanded polystyrene slabs density and porous structure as well as establish mechanism of deformation and effects of compressive load on the structure.

323

第1页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email