直线电机 linear motor
Calculation of Temperature in the Permanent
Magnet Tubular Linear Motor
A. Waindok, Member, IEEE
Abstract— The calculation results for the thermal field of the permanent magnet tubular linear motor (PMTLM) have been presented in the paper. For the analysis of heating, four different mathematical field models have been created. Each of them uses the finite element method (FEM). In the most simplify model only the standard convective heat transfer coefficient has been
III.MATHEMATICAL MODELimplemented. In the most sophisticated model, thermal radiation,
convective heat transfer and dependence of the coil resistance vs. The thermal model is based on the thermal field analysis, temperature have been included. The numerical models have
carried out after solution of the Poisson equation [5], which
been verified experimentally.
implemented in different devices e.g. in CNC machines. The motor is supplied with a pulse width modulation signal. The maximum current and force value are Imax=8 A and Fmax600 N, respectively. The nominal current value is IN=2.7 A.
describes the static temperature distribution in the device
Index Terms—Linear motors, thermal field calculations, (κ T)= pthermal radiation phenomenon.
(1)
I
where: p [W/m3] – power density generated in the unit
I.INTRODUCTIONvolume, κ [W/(m·K)] - coefficient of thermal conductivity
N the designing of electrical devices not only the calculation (for the anisotropic medium the coefficient represents a tensor of electromagnetic parameters is important, but also the quantity), T



[K] – the temperature of the analyzed area. calculation of heating. In the paper four models of permanent magnet tubular linear motor (PMTLM), created with using the finite element method (FEM) are presented. The correct determination of the motor heating is related to the limitations of the permanent magnet work temperature [1, 2]. In two of the models, the modification of the boundary condition for convective heat transfer coefficient by the improvement of the nonlinear component describing the radiation phenomenon, has been used. The execution of multi-variant calculations required the creation of the original algorithm, which enabled developing of the adequate, nonlinear boundary condition for consideration of both thermal convection and radiation.
Fig. 2. Cross section of the model including the boundary conditions
Fig. 1. Picture of the motor
II.PHYSICAL MODEL
The calculations have been carried out for a 5-phase tubular linear synchronous motor (Fig. 1) [3, 4]. The actuator could be
This work was supported in part by the Polish Ministry of Science and Higher Education under grant no. N N510 533739.
A. Waindok is with the Opole University of Technology, 45-758 Opole, Poland (phone: 48 77 449 80 27; e-mail: a.waindok@po.opole.pl).
Two boundary conditions have been used. The first one concerns the fixed value of the environmental temperature T0on the outer boundary of the analyzed region, i.e. the room temperature (Fig. 2). The second one is the surface condition for the convection. The total heat flux, crossing the outer surface of the actuator construction, is directly proportional to the temperature difference and heat transfer coefficient h [W/(m2·K)]:
&
κ T n+h(T T0)=0 (2) To take the radiation phenomenon into account, the equivalent, nonlinear heat transfer coefficient heq has to be defined [5]:
3
§T+T0·
heq=h+4σε¨¸ (3)
©2¹
978-1-4673-5590-2/13/$31.00 ©2013 IEEE
Calculation of temperature distributions in the rotors of oil_injected screw compressors 隐藏>> International Journal of Thermal Sciences 50 (2011) 1271e...
Temperature Calculation and Prediction of Gas Hydrates Formed Region in Wellbore in Deepwater Drilli_建筑/土木_工程科技_专业资料。Proceedings of the ...
19_Numerical Calculation of the Cooling Rate in the J-Quenching Technique_...Setting the appropriate parameters, a series of temperature pro?les ...
Calculation Method of ... 1人阅读 5页 2.00Simulation analysis ...
The calculation of hydrocarbon-generating temperature--Theory and practice_专业资料。维普资讯 http://www.cqvip.com ChnJGehm.082:9-17i.oe(0)7149 .c2D0Il...
Calculation of Semiconductor Failure Rates William J. Vigrass One of the ...the internal temperature rise of the device to represent the junction ...
elementanalysis.Tovalidatethecalculationresultbefore,thedemagnetizationtestingwasproceededunderan assumptionofworstconditionsofinputcurrentandtemperature,whenthepermanent...
calculation of phased array noise temperature___相控阵噪声温度计算_信息与通信_工程科技_专业资料。Calculation of phased array noise temperature Bert Woestenburg...
1 First-principles calculation of the temperature dependence of the optical response of bulk GaAs Z. A. Ibrahim (1), A. I. Shkrebtii* (1), M. ...
First-principles calculation of the structure and the energy of ZrO2 Al2O...The cubic phase of ZrO2 (c-ZrO2) is the high-temperature polymorph, ...
热门文档