文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > SAE J323-2004
侵权投诉

SAE J323-2004

标准

SURFACEVEHICLE

RECOMMENDEDPRACTICE

An American National Standard

J323

REV.JAN2004

1968-082004-01

IssuedRevised

Superseding J323 JUL1998

Test Method for Determining Cold Cracking of Flexible Plastic Materials

1.

Scope—This SAE Recommended Practice is applicable for determining the cold characteristics of flexibleplastic materials, as applicable. It consists of three different methods for determining low-temperatureproperties of materials depending on type of material and end use.References

Applicable Publications—The following publications form a part of the specification to the extent specifiedherein.

ASTM PUBLICATION—Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.ASTM D 3574—Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded

Urethane Foams

2.2.1

2.1.1

3.3.13.1.1

Method A, Mandrel TestApparatus and Materials

MANDREL—Steel mandrel nominally 6.35 mm in diameter and 152 mm long attached to a suitable stand.Other diameters may be specified depending on the thickness and rigidity of the material to be tested.OVEN—Air-circulating oven capable of maintaining a temperature of 82 °C ± 2 °C.

COLD BOX—A cold box capable of maintaining a temperature of 34 °C and large enough to permit bendingthe test specimen while it remains in the box.

GLOVES—Heavy cloth gloves to prevent heat transfer when handling specimens.

Procedure—Cut 50 x 200 mm specimens in the machine and across machine direction and condition in theoven at 82 °C for 24 h or as specified. (The dimensions of the specimen may vary for extruded or moldedparts.) Remove specimens from the oven and condition at room temperature until reaching equilibrium. Placespecimens, gloves, and mandrel with stand in the cold box at 34 °C for 4 h or as specified. Put on gloves andgrasp each end of the sample and bend, around the mandrel in approximately 0.5 s with a uniform motion.Remove specimens from cold box and examine visually for evidence of cracks.

3.1.23.1.3

3.1.43.2

SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirelyvoluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.”

SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.Copyright © 2004 SAE International

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER:

Tel: 877-606-7323 (inside USA and Canada)Tel: 724-776-4970 (outside USA)Fax: 724-776-0790

Email: custsvc@sae.org

SAE J323-2004

SAE J323-2004

doc.guandang.net

Licensee=Lear - Southfield/5910410001, User=simon, edNot for Resale, 09/28/2007 06:01:14 MDT

SAE WEB ADDRESS:

Copyright SAE International

Provided by IHS under license with SAE

No reproduction or networking permitted without license from IHS

第1页

你可能喜欢

热门文档

相关文档

  • SAE标准

    SAE J2667 测试方法为了决定柔韧性塑胶材料的寒冷破裂 J-323-2004 SAE J-323-04,SAE J-323,SAE J323-2004,SAE J323-04,SAE J323 术语-水力的锄耕机 <...

  • ASTM D 6695-2008

    同系列文档 SAE J322-1996 SAE J323-2004 ASTM D 429-2008 ASTM D 6110-20081/2 相关文档推荐 ASTM D 1622-2008 4页 5财富值 ASTM D 429-2008 22页 ...

  • ASTM D 6695-2008

    同系列文档 SAE J322-1996 SAE J323-2004 ASTM D 429-2008 ASTM D 6110-20081/2 相关文档推荐 ASTM D 1622-2008 4页 5财富值 ASTM D 429-2008 22页 ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email