P.O. No. 订单号 Shipment Quantity 出货数量 S-2 Sample size 尺寸功能抽检数量S-2 S-4 Sample size 真空泄露测试抽检数量S-3 Product Description 产品描述
Date 时间 Inspector 检验员 Manufacturer 工厂 Location 地址 (Trigger Sprayer喷枪) Special Inspection Level S-2 Number of Rejects不良数 AQL Level 0.4 0.65 1.5 0.65 -----
ITEM 检验项目 1 Dip tube pull force:≥10N 吸管的拉掉力:≥10牛顿 2 Nozzle pull force :≥50N 的拉掉力:≥50牛顿 喷嘴
REMARKS 备注
0.65 0.65
-----
-----
3 Closure check,Closure turns freely when not screwed on bottle,Closure deosn't turn freely when screwd on bottle 螺牙盖:当喷枪未旋紧于瓶时,螺牙盖能轻易旋动,螺牙盖配签样瓶或 标准瓶扭紧后,枪体不能轻易被旋动. 4 Use a standard/customer plastic bottle to check the pump thread fit. Should be smooth, without crooked head and etc visual defects 螺牙配合签样瓶或标准瓶,顺畅,无歪头,等外观缺陷. 5 Integrity of pump, drop three times from 1.5m (5 feet) height on side with no damage. 泵的装配紧密性,1.5 米跌落3次,无零件脱落。 6 Vacuum test,Follow S-3 inspection level for this test only。4 minutes at -0.05MPa, using water. 真空测试,在-0.05MPa,放置4分钟,用水测试不泄漏。根据S-4 抽检标准。 7 STP:≤7 times (DTL<200mm) 起喷次数: ≤7次 (吸管长度小于200毫米,超过200毫米,起喷次数 可适当增加) 8 No prime or STP more than 20 times 不能喷或者 STP 大于20次 9 Dynamic leak test:The trigger sprayer must pass the dynamic leakage test ( maximum 1 drop every 25 strokes,actuating spees is 60-90times/minute.) 喷雾漏液测试:喷雾时,喷咀孔或其它部位不能有漏液情况( 每喷 25次不能漏超过一滴,按压扳手的速率为60-90次每分钟) 10 Spray pattern :the spray pattern of the trigger matching the nozzle sign and PO specification. 喷出液体形状:喷出液体形状要为指定的雾状或线状或泡沫。 0.7c Check the output of the trigger. It should be per P.O +/-10% 检查喷枪的喷出量,这要符合订单的要求+/-10%(喷出量取10次喷出 量的平均值) 12 Valve flexibility ;Valve should be flexible, without black rubber is allowed. 阀门弹性:阀门弹性良好,不能是黑橡胶。 13 Spring quality Follow S-1 inspection level for this test only 弹簧测试跟据S-1抽检标准 14 Pump can be actuated 50 times without malfunction. Unless otherwise specified. Follow S-1 inspection level for this test. 按压喷枪50次,功能正常;如果发现功能异常,按S-1抽样,做进 一步测试。 15 Venting test:The trigger bottle won't be deformed after 20 times of stroke (screw the trigger on soft bottle before testing) 回气测试 :旋紧喷枪到装满液体的薄壁瓶子上,快速喷液20次 后,瓶子表面不允许有凹陷的情况。 16 "On" Position leakage test:Prime the trigger and lay the b
ottle on its side on "ON" (spray/stream) position. No water leak more than 1cc within 1min. 打开状态漏液测试:上液之后将喷枪平躺,1分钟内漏液不能超过 1cc. 17 Nozzle torque 1.0lb.in to 3.3 lb.in 喷头的转动扭矩为1-3.3lb.in 18 Check the length of the dip tube; it should be per p.o. -/+1mm. (If applicable) +/-2mm if the Dip tube length exceeds 180mm PE material). 检查吸管长度, 如果长度小于200mm,误差范围-/+1mm; 如果长度大于或等于200mm,误差范围-/+2mm 19 Shroud not loose, pull force ≥20N or passed shaking testing 罩壳的拉掉力:≥20N牛顿或者通过摇摆测试 20 (If applicable) minimum plastic mesh insert pull force -- 20N (如果有泡沫网孔)最小塑料泡沫网孔拉掉力为20牛顿 21 Pump piston activity,smooth during actuation (subjective) 活塞活动性,按压时活动上下顺畅(手感)
0.65
---
---
0.65
---
---
0.40
---
---
0.65
---
---
0.65
0.65
---
---
0.65
---
---
0.65
---
---
0.65
---
---
0.65
---
---
0.65
---
---
0.65
---
---
0.65
---
---
0.65
---
---
0.65
---
---
0.65
---
---
0.65
---
---
0.65
---
---
Totals Dimensional check Dimension 尺寸 1 Closure OD 螺圈外径 2 H Dimension 螺圈深度 3 Total trigger height 喷枪总高 4 T dimension T值 5 E dimension E值 AQL Level 0.65 0.65 0.65 0.65 0.65 Standard 标准 Remarks 备注




12345
Trigger Sprayer checklist 01-05-10 隐藏>> P.O. No.订单号 Shipment Quantity出货数量 Total quantity of cartons 总包装箱数量 Sampling quantity of cartons ...
同系列文档 Trigger Sprayer checklis...相关文档推荐 暂无相关推荐文档搜你所想,读你所爱 拒绝盗版,营造绿色文库 如要投诉违规内容,请到百度文库投诉中心;如要...
STP:≤7 times Dynamic leak test:The trigger sprayer must pass the dynamic leakage test ( maximum 1 drop every 25 strokes) Spray pattern :the spray ...
STP:≤7 times Dynamic leak test:The trigger sprayer must pass the dynamic leakage test ( maximum 1 drop every 25 strokes) Spray pattern :the spray ...
热门文档