文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 电子/电路 > Speed sensorless robust torque control of induction motor
侵权投诉

Speed sensorless robust torque control of induction motor

Speed Sensorless Robust Torque Control of

Induction Motor

Karel Jezernik

University of Maribor, Faculty of Electrical Engineering and Computer Science, Smetanova 17, 2000 Maribor, Slovenia

karel.jezernik@uni-mb.si

Abstract- A new, the torque and speed sensorless induction motor control is proposed, analyzed and experimentally verified in this paper. The control is based on stator and rotor flux as state variables. This choice of state variables allows a graphical representation which is transparent and insightful. A speed sensorless implementation of the control is demonstrated experimentally for low speed operation. Proposed control scheme is implemented on DSP system extended with FPGA circuit. Experimental results demonstrated high efficiency of the proposed estimation and control approach.

I. INTRODUCTION

A. Machine Dynamics

Control of induction motor (IM) is still a challenging problem due to its nonlinear dynamics, limited possibility to measure or estimate necessary state variables and presence of the switching converter with its own nonlinearity as a power modulator in control loop. The dynamics of IM consist of mechanical motion (5), dynamics of stator electromagnetic system (1) and the dynamics of the rotor electromagnetic system (2): dΨSRRL

=uS SΨS+SmΨR, (1) dtσLSσLSLR

Recent theoretical advances in the field of hybrid dΨRLRR

=+RmΨS RΨR+jpωRΨR, (2) and discrete event-systems, and significant increase of the

dtσLRLRσLR

computational power available for the control of the power

electronic systems are inviting both the control and the power Ψ=LmΨ+σLi, (3)

SRSS

LRelectronics communities to adopt traditional control schemes

associated with power electronics applications. In order to 2Lm

ΨR×iS (4) raise the performance and efficiency of the drive applications, Te=p3Lr

faster and more sophisticated current control schemes are

required. The conventional current control scheme consisting dωr=1(T T) (5)

eL

of discrete-time current controller and pulse-width modulator dtJ

is replaced with the new sequential switching current control where ωR is mechanical rotor angle speed, the two

T

strategy. Inherent switching operation of the three phase dimensional complex space vectors ΨS= ΨΨ, SaTSb , TTbridge requires adopted control principles. Hysteresis ΨR= ΨRa,ΨRb , uS= uSa,uSb , iS= iSa,iSb are controllers can be a good alternative for such applications. stator and rotor flux, stator voltage and current, respectively, They are robust to system parameter variations, exhibit very Te is motor torque, TL is load torque, J is inertia of the good dynamics, require simple implementation and enable rotor and p is the number of pole pairs.

direct control of the bridge transistors without special One of the most important issue in implementing direct modulators. Their main drawback is a limited control of torque control (DTC) or field oriented control (FOC) transistor switching frequency [1],[2]. strategies for IM is to obtain real-time instantaneous flux In this paper by combining the variable structure system level and position with sufficient accuracy for the entire and Lyapunov design [3] a novel sliding mode algorithm of speed range, from almost standstill to high speed level. The controller/observer for induction motor is developed. This difficulty in flux estimation lies with the non-linear induction control method is based on estimation of the rotor flux and machine model, which is characterized by speed dependent speed of IM and is due to use of sliding mode principle robust and time varying parameters. In order to illustrate this non-against variation of load torque, machine parameters and linear behavior of IM control let us express the derivation of external disturbances. For both, controller and observer, there developed electrical torque of IM from (4). This yields for are used nonlinear control principles, namely estimated EMF torque variation: and machine terminal voltage built a nonlinear feedforward dT RR 2pLme

+ S+R Te=(ΨR×us pωrΨS ΨR),control, sliding mode principle based on state variable errors

dt σLSσLR 3σLSLR

are used as feedback to guarantee stability of control system.

The proposed method is investigated and verified in hardware (6)

where × indicates cross product and indicates dot product. in the loop simulation experimentally.

It can be recognized from (6), that torque variation is the sum

of two terms. The first term depends on the stator (RS) and

II. DYNAMIC MODEL OF INDUCTION MOTOR

rotor (RR) resistance and reduces the absolute value of the

第1页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email