文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 电子/电路 > H15234中文资料
侵权投诉

H15234中文资料

H15234中文资料

元器件交易网doc.guandang.net

TECHNICAL DATA / BLACK-AND-WHITE INTERMEDIATE FILM

March 2004 H-1-5234t

EASTMAN Fine Grain Duplicating Panchromatic Negative Film 2234, 3234, 5234, 7234

EASTMAN Fine Grain Duplicating Panchromatic Negative Film 5234/7234 and EASTMAN Fine Grain Duplicating Panchromatic Negative Film 2234/3234, ESTAR Base, are characterized by very high sharpness. They have

panchromatic sensitivity. These low-speed, black-and-white films are designed for making duplicate negatives from master positives, or internegatives from reversal originals. When used with EASTMAN Fine Grain Duplicating Positive Film 5366/7366, they produce negatives nearly equal to the original negative in tone rendering and printing detail.

BASE

5234/7234 Film has a gray acetate safety base. The back side of the base contains an anti-static layer with a carnauba wax lubricant.

2234/3234 Film has a gray ESTAR (polyester) base. The backside of the base contains a process-surviving anti-static layer.

DARKROOM RECOMMENDATIONS

Use a KODAK No. 3 Safelight Filter / dark green, with a 15-watt bulb, no closer to the film than 1.2 metres (4 feet).

STORAGE

Store unexposed film at 13°C (55°F) or lower. For extended storage, store at -18°C (0°F) or lower. Process exposed film promptly. Store processed film according to the recommendations in ANSI/PIMA IT9.11-1998: for

medium-term storage (minimum of ten years), store at 25°C (77°F) or lower at a relative humidity of 20 to 50 percent; for extended-term storage (for preservation of material having permanent value), store at 21°C (70°F) or lower at a relative humidity of 20 to 30 percent. For active use, store at 25°C (77°F) or lower, at a relative humidity of 50 +/- 5 percent. This relates to optimized film handling rather than preservation; static, dust-attraction and curl-related problems are generally minimized at the higher relative humidity. After usage, the film should be returned to the appropriate medium- or long-term storage conditions as soon as possible.

For more information about medium- and long-term storage, see ANSI/PIMA IT9.11-1998, SMPTE

RP131-1998, and KODAK Publications No. H-1, KODAK Motion Picture Film, and No. H-23, The Book of Film Care.

PROCESSING

The following process recommendations should be used as starting points for most conventional continuous-immersion processors with solutions prepared according to the formulas in KODAK Publication No.H-24.15, Manual for Processing KODAK Motion Picture Films, Module 15. The processing times may require modification for a particular machine.Note: Observe precautionary information on product labels and on the Material Safety Data Sheets.

Processing

Temperature

Time

Replenishment

Step

Rate

(mL per 100 ft)35 mm

16 mm

KODAK Developer70 +-1/2 F1250625 D-961 (21 +-0.3 C)-2 (D-96R)(D-96R)Stop Rinse370 +-2 F (21 +-1 C)50 sec12,0006000KODAK Fixing Bath70 +-2 F6 min850425 F-51

(21 +-1 C)Wash

70 +-2 F(counter-current) (21 +-1 C)10 min12,000

6000

Dry

95 F (35 C)

-4

1 Agitation in the developer and fixing bath should be by recirculation

through submerged spray jets that impinge on the film strands.

2 Develop to recommended control gamma.

3 Countercurrent flow of fixer-laden water overflow from the wash tank, pH

about 6.

4 Many factors affect the drying: air temperature, relative humidity (RH);

volume, rate and distribution of the air flow; final squeegeeing, etc.

In a conventional convection-type drying cabinet with air at about 95°F (35°C) and 40 to 50 percent RH, drying will take 15 to 20 minutes. With an impingement-type drying cabinet, however, with a higher temperature and lower RH, drying time is greatly reduced. With either type of dryer, the film should be dry without tackiness 1/2 to 2/3 of the way through. Upon cooling to room temperature after leaving the dryer, the film should be in equilibrium with the room air at approximately 50 percent RH.

IDENTIFICATION

After processing, the product code numbers 2234, 3234, 5234, or 7234; emulsion and roll identification; and

KEYKODE number (KD) are visible along the length of the film.

第1页

热门文档

相关文档

  • lm311中文资料

      ?   713Z[      海纳电子资讯网:www.fpga-arm.com 为您提供各种IC中文资料 ...

  • SG3525中文资料

    SG3525中文资料_信息与通信_工程科技_专业资料。电子3525 总结 nan’sir SG3525 电压调节芯片 SG3525 具体的内部结构如图 1 所示。其中,脚 16 为 SG3525 的...

  • FT2232中文资料

    FT2232 中文资料 FT2232 中文资料 1 FT2232C 概述 1.1 电路概览 FT2232C 是一款 USB 到 UART/FIFO 的转换电路,是 FTDI 公司继第二代 FT232BM、 FT245BM 之后...

  • SR540中文资料

    SR540中文资料_信息与通信_工程科技_专业资料。SR520 – SR560 5.0A SCHOTTKY BARRIER RECTIFIER Features ! ! ! ! ! ! Schottky Barrier Chip Guard Ring ...

  • AT89C52中文资料

    http:// www.ourmpu.com E-mail:support@ourmpu.com QQ:451338524 电子驿站 1 476485321 AT89C52 中文资料 AT89C52 方框图 更多的单片机资料、源程序及单片机教程...

  • STC89C52中文资料

    单片机中文指南(RC/RD+ 系列)4 海纳电子资讯网:www.fpga-arm.com 为您提供各种IC中文资料 STC89C51RC/RD+ 系列单片机 ISP 编程 原理 注意事项 单片机彻底没电 ...

  • LM7912中文资料

    LM7912中文资料_电子/电路_工程科技_专业资料。LM7912中文资料LM7912 中文资料(引脚图,电气特性参数,应用电路) 负 12V,1A 三端稳压器 LM7912 中文资料(引脚图...

  • SMAJ16CA中文资料

    SMAJ16CA中文资料_信息与通信_工程科技_专业资料。SMAJ5.0(C)A - SMAJ440(C)A 400W Surface Mount Transient Volage Suppessor Features 400W Peak Pulse Pow...

  • 7805中文资料

    7805中文资料_信息与通信_工程科技_专业资料。7805中文资料,7805稳压电源电路图,7805引脚图,LM7805,7805输入电压,7805资料,LM7805,7805中文资料下载,LM7805引脚图,...

  • LCD1602液晶完整中文资料

    LCD1602液晶完整中文资料_理学_高等教育_教育专区 暂无评价0人阅读0次下载举报文档 LCD1602液晶完整中文资料_理学_高等教育_教育专区。这是我用3天时间整理的,...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email