SPE# 36230 Oil and Water Flow Rate Logging in Horizontal Wells Using Chemical Markers and a Pulsed-Neutron Tool. B, IBmll<l.4. Rmcuc, .7chlt[tttherger-Doll Research& Chris Lentr, Schhwtberger Oillicld .-1 S.VI.V!OIICC, Ltd. 1N-I
CwyfiOht j 996, Sodefy of Pe!m4eumEnQimeers Inc This paper was prepared for presentation al the 7th Abu Dhabl Intemalional Patroleum Exhwbon and Conference hOIdh Mu Dfw.ti U.A.E., 13-16 October, 19W This papef was selected for presanlafkm by an SPE Pqram Commttrea fdlowmg review of infonnabw! contained in an abstract suLbntttedby the autfwr(s) Ccmtenls of the papar, ss presented, have c-albeen revwwed by fh4 Sockly of PeUc4eum Engirwem and am subfect to refk.ct any correction by the author(s). The material, as presented, does notnecessarily psifion of the See-sly of Pdmlnum Engmsem, ils ofkm% w members Papas presented at SPE meefmgs are subject to F4Mcatmn rewew by Editorial Committees of Ihe Society of Petrdewn Engineers. Permissw. to copy IS restncled to 8. qbstiacl of“ot more than 300 words. Illustrations may not be copied. The sbatract should contain conspmuo. s dnowledgmen( of wtmm and by whcin the pe.pw was Vesemted. Write Librarian, SPE, P.O Box 633S36, Rtimdson, TX 7SOS3-3S36, U S A., *X 01-214-952-9435
Abstract A new approach to obtaining oil and water flow rates in producing horizontal wells has been developed using a pulsedneutron tool. This approach uses separate measurements of oil and water velocities in combination with separate holdup measurements to obtain the flow rates. The velocity measurement uses both water-soluble and oilsoluble chemical markers, each of which is insoluble in the other fluid phase for the measurement. The markers are injected into the borehole by a logging tool at one location and detected by a pulsed-neutron tool at a second location. The transit time between injection and detection of the marker gives a measurement of the fluid velocity. Since the markers are soluble only in one phase, the velocity of each phase can This measurement has been made be measured separately. under both laboratory and field conditions to measure velocities from 10 to 500 ft/min at horizontal and several degrees deviation from horizontal. The results of these tests show good linearity and repeatability of the measurement. The holdup measurement is performed using the inelastic data from a pulsed-neutron tool. With these data, it is possible to quantitatively obtain the holdup of all three phases by combining information from the inelastic near/far ratio with the near and far carbon/oxygen ratio. This approach to the holdup measurement has been demonstrated using a combination of laboratory data, Monte Carlo modeling, and field data. The results of this study have demonstrated that the RMS accuracy of this measurement is about 6% on each of the three phases. Introduction As horizontal wells have become more prevalent, the ability to reliably evaluate the production performance of these wel]s
has b
ecome increasingly important. Existing production logging techniques, such as spinners, that have been successfully used in vertical wells can not always be applied to horizontal wells with full confidence due to the segregated flow in the borehole. For this reason, new techniques must be developed to evaluate oil and water flow rates in horizontal wells. To determine the flow rates of the oil and water phases in a horizontal well, one must either 1) measure the individual oil and water flow rates directly, or 2) measure the individual oil and water velocities in addition to their holdups. (It should be noted that for most production logging applications in horizontal wells measuring only the holdup or only the velocity of the production fluids is usually insufficient to determine the source of production problems.) This paper will address the second approach dealing with the measurement of individual oil and water velocities and their holdups. Oil and Water Velocity Measurement Several existing technologies make it possible to measure water velocity in horizontal wells. The oldest of these uses a radioactive tracer such as Iodine-131 with an 8 day half-life.’ The iodine is placed in a water-soluble form. This material is injected into the borehole and then measured as it passes a gamma-ray detector. The time between injection and detection allows calculation of the flow velocity of the water. This method can also be applied with some success to oil velocity measurements by placing the iodine into an oilsohsble form. The limitation in this approach is that the oilsoluble form is usually an emulsion that can exhibit some unique problems due to the nature of emulsions. With the increased restrictions and risks associated with the use of radioactive tracers in the borehole, it is desirable to have a method of performing these velocity measurements without using radioactive tracers. This is one of the reasons that the W FL* Water Flow Log was developed. This approach relies on the activation of oxygen in the water using a 14 MeV neutron generator and measures the transit time of the activated oxygen in the borehole2 giving a measure of the water velocity. Unfortunately, this method does not address the oil velocity measurement.
q
Mark of Schlumberger
-583-

“Fracking gives Texas another oil boom, but at...Typical Flow Chart Water Sources Mixture Disposal ...wells and 30% in horizontal wells, but with ...
logging, and more recently, downhole temperature ...inflow rate along 2 SPE 131370 horizontal wells....We use synthetic water-oil examples with two ...
Horizontal wells can decrease well productivity. ...A drill string and logging tools can become ...Water-based muds use liquid oil as the ...
Geosteering Horizontal Wells_能源/化工_工程科技_专业...and other mud logging data, can be successfully ...(Wh and Bh cross over) and oil-water contacts...
穆立婷 110 operation for horizontal wells of Tarim...flow rate water nozzle in water injection ,the ...logging data ,process and analysis for the ...
the mature oil fields in east China are in a stage of high water cut....Data are abundant and includes core data, horizontal wells, logging data, ...
no gas cap and no water drive, drilling of horizontal wells would likely ...similar to those obtained by conventional wire line well logging methods, but...
Wireline Production Logging 电缆生产测井 ? Wireline...water bearing sand in the horizontal snaking ...oil reservoir in the Middle East Wells generally ...
water stratified flow in the highly deviated or the horizontal gas wells, ...Keywords holdup rate electromagnetic image logging; gas -water stratified flow...
logging has been the backbone of oil and gas ...and completion of oil and gas wells from an ...true horizontal – and the direction of the dip...
热门文档