IGBT模块内部杂散电感定义方法
from Europefor the World
Application


Note
Semiconductor andElectronics Company
Definition of the module stray inductance Ls
Fig.1 shows the principle circuit of a half-bridge and the resulting voltage and current wave-forms when switching IGBT1. The circuit stray inductance Lσ, shown as a concentrated ele-ment, represents all distributed inductances (of capacitors, busbars and IGBT modules)within the commutation loop (striped area).




VGE


V0
IID2
VFig.1: Half-bridge circuit with current and voltage waveforms when switching IGBT1
Due to the changing current a voltage drop of Lσ * dioff/dt occurs across the stray inductanceLσ. It is overlayed to the DC link voltage VCC and seen as a voltage spike across the turning-off IGBT1. Permissible limits for turn-off current di/dt and overvoltage can be deduced fromthe RBSOA diagram of the IGBT. This curve (see Fig.2) is valid when the measurement isdone through the CE auxiliary terminals. Also a derated curve is given in the data-sheet formeasurements at the power terminals, taking into account the internal module stray induc-tance between main and auxiliary terminals of the module. For dual modules, this diagramsrefers to the voltage across one of the both commutating IGBT switches.
For calculations the value for the internal module stray inductance Ls is given in the data-sheets. For single switch modules, this value is the before mentioned stray inductance be-tween main and auxiliary terminal. For dual modules or modules containing several phaselegs, this value corresponds to the application relevant effective commutation loop betweenupper and lower switch. Due to the construction this value is clearly lower than the sum of
eupec
Marketing DepartmentMax Planck Str. 5D-59581 Warstein
Tel:+49 2902 764-0Fax:+49 2902-764-1256
Internet:: doc.guandang.net
AN_Stray_Inductance_Definition.doc
IGBT 模块内部杂散电感的定义 IGBT 半桥逆变电路工作原理以及当 IGBT1 开通关断时的电压电流波形如图 1 所示, Lσ代表 整个换流回路(条纹区域内)所有的杂散...
IGBT杂散电感参数计算_电子/电路_工程科技_专业资料。IGBT关断过电压计算,... IGBT模块内部低电感设计 2页 免费 IGBT复合母排换流回路电... 3页 免费...
Collector-emitter voltage of the IGBT 由于模块内部杂散电感,模块主端子与辅助端子的电压差值为 ,由于内部 及外部杂散电感,VCES 在 IGBT 关断的时候最容易被...
开关频率越来越快趋势下, 由于杂散电感引起的电压尖峰的影响越来越大, 我司的风能变流器大量使用IGBT模块,准确可靠地对IGBT电路的杂散电感 进行测量显得十分重要。...
电路中杂散电感的测量方法 2页 免费 IGBT模块内部低电感设计 2页 免费 电感设计 18页 2财富值喜欢此文档的还喜欢 典型叠层母排的应用案例 12页 2财富值 ...
模块与 IGBT 模 块集电极 c 之间的电压不能连续可调.在实际工作中,改进方法有...(1),尽可能减少电路中的杂散电感.作为模块设计制造者来说,要优化模 块内部...
低电感薄型IGBT模块 7页 1财富值 IGBT模块内部杂散电感定义... 3页 免费 ... IGBT模块内部低电感设计 IGBTIGBT隐藏>> 1.55 LσC TOP LσG LσEC ...
IGBT模块在端子上引起的过电压 由杂散电感引起的压降 Norbert Pluschke 0807 5 ...直流母线电感 模块内部过电压+ 模块主端子的过电压 模块内部过电压 Norbert ...
应用中常常因寄生电感产生过电 内部结构 ,减少模块寄生电感 ; ② 使用者优化主...3 IGBT 关断时的过电压 由于关断时总会有过电压 , 所以完全消除杂散 电感是...
2.3 高端模块 高端 IGBT 模块其内部电路结构如图 3(a)和图 3(b)所示。...同时,必须尽量减少或者消除布线时的杂散电感,可以通过减小整个电路有效 回路面积...
热门文档