Industrial Compressor Anti-Surge Computer
Control
Ventzas Dimitrios, and Petropoulos George
Abstract—The paper presents a compressor anti-surge control
system, that results in maximizing compressor throughput with pressure standard deviation reduction, increased safety margin between design point and surge limit line and avoiding possible machine surge. Alternative control strategies are presented.
Keywords—Anti-surge, control, compressor, PID control, safety, fault tolerance, start-up, ESD.
The input signals are the suction flow differential pressure, suction pressure and discharge pressure, see Fig. 2. A temperature measurement corrects flow and speed at the compressor suction.
Surge detection devices are static and dynamic ones. The pressure transmitter monitors the pressure and controls the blow-off valve to avoid stall and surge. Surge cycles occur fast and can even go undetected if the applied instrumentation and controls are too slow.
III. COMPRESSOR SURGE
Compressor surge occurs when the developed compressor head (H) drops below the network resistance (discharge pressure). Surge is a fluctuation of flow and pressure and it causes overheating and damages; it may be violent enough to damage a compressor in a few cycles. Surging gives cyclic flow, back-flow, high vibrations, pressure shocks and rapid temperature increase. Process design minimizes the piping volume in the recycle and forward path [1].

HE compressor is a multi-stage type; the incoming air is compressed in the first stage and then passed through a heat exchanger to be cooled off before being injected into the next stage, see Fig. 1.
Anti-surge control system design practices encompass the proper sizing, selection, and location of piping of the recycle loops, the recycle valves, volumes of vessels in the recycle path, check valves, etc..

T
I. INTRODUCTION
Fig. 1 Compressor details
II. INSTRUMENTATION AND ACTUATORS

Fig. 2 Required input signals
Fig. 3 Momentary flow reversal
Ventzas Dimitrios is with Department of Informatics & Communications, TEI of Larissa, Larissa 41 100, Greece (e-mail: dventzas@uth.gr).
Petropoulos George, Associate Professor is with Department of Mechanical Engineering, University of Thessaly, Greece (e-mail: gpetrop@uth.gr).
An increase in pressure across the compressor, results in a momentary flow reversal, see Fig. 3. This surge cycle goes until a change is made in the process conditions. The controller operates a surge valve to maintain sufficient
industrial production process, Surge phenomenon, ...The hardware circuit design of one-chip computer ...Key words:centrifugal compressor;anti-surge;8051;...
Compressor & Surge Control TPG_能源/化工_工程科技_专业资料。压缩机及防喘振控制原理Axial Compressor Control Technical Product Guide Single Stage Inter-cooled ...
Industrial, Two-Shaft ? Axial Compressor – 15-Stage – Variable Inlet ...Compressor Anti-Surge Control – Field Programming – Predictive Emissions ...
? ? 90 Gas Turbine Industrial, Two-Shaft Axial Compressor – 15-Stage –...Compressor Anti-Surge Control – Field Programming Start Systems – Pneumatic ...
Compressor Anti-surge Design 袁蓉 * 向兆永 刘文艳 YUAN Rong XIANG ZHao-...hardware failure remote positioning advanced computer network technology to achieve...
Industrial, Two Shaft ? Axial Compressor – 12 Stage – Variable Inlet ...– Process Controls – Compressor Anti-Surge Control – Field Programming ? ...
Industrial, Two-Shaft ? Axial Compressor – 8-Stage – Compression Ratio: ...– Process Controls – Compressor Anti-Surge Control – Field Programming ? ...
Industrial, Two-Shaft ? Axial Compressor – 11-Stage – Variable Inlet ...– Process Controls – Compressor Anti-Surge Control – Field Programming ? ...
Industrial, Two-Shaft ? Axial Compressor – 11-Stage – Variable Inlet ...– Process Controls – Compressor Anti-Surge Control – Field Programming ? ...
Industrial, Two-Shaft ? Axial Compressor – 11-Stage – Variable Inlet ...– Process Controls – Compressor Anti-Surge Control – Field Programming ? ...
热门文档