4. EB-PVD process and thermal properties of hafnia-based thermal barrier coating
ELSEVIER
Surface and Coatings
Technology
86-87 (1996) 94-101
Improved tetragonal phase stability at 1400°C with scandia, yttria-stabilized zirconia Robert L. Jones a3*,Derek Mess b a Code 6170, Chemistry Division, Naval Research Laboratory, Washington, DC 20375-5342, USA b Cambridge, Microtech, Inc., 100 Inman Street, Cambridge, MA 02139-l 206, USA
Abstract Sol-gel prepared plasma spray powders of Sc,O,,Y,O,-stabilized ZrO, (SYSZ), where the total amount of stabilizer is -7 mol.%, and the stabilizer contains 2.5520% Y,03, have been found to give significantly better tetragonal (t’) phase stability at 1400°C than present-day Y,O,-stabilized ZrO, thermal barrier coating (TBC) material. The results are discussed in the context of
the ongoing effort to develop ZrO,-based (or other) ceramics suitable for ultra-high temperature TBC usage. Keywords:
Tetragonal phase stability; Scandia,yttria-stabilized zirconia; Thermal barrier coating; Ultra-high temperature
1. Introduction The most important factor in determining gas turbine (GT) engine power and fuel efficiency is the gas operating temperature. Many“generations” of blade superalloys have been developed over the last 25-30 years to increase the temperature at which gas turbines operate. However, this has been an expensive and difficult task. As shown in the review by Kool[ 11, this effort, which includes the development of exotic casting techniques to produce directionally solidified and single-crystal blades, has succeeded in improving blade superalloy temperature capability by about lOO-125”C, i.e., from 1000°C in 1965 to 1100-l 125°C in 1990. Moreover, Ni-based superalloys are thought to be now developed to very near their maximum temperature capability (which is ultimately limited by incipient melting). The use of zirconia-based thermal barrier coatings (TBCs) on blades is currently being considered as a means for increasing gas temperatures to still higher levels in high efficiency gas turbines. Fig. 1 shows a schematic cross-section of an electron beam-physical vapor deposited (EB-PVD) thermal barrier coating of the type proposed for GT blade usage. Because of the heat insulating properties of ZrO,, the TBC reduces the temperature seen by the metal of the air-cooled blade by as much as lOO-200°C. TBCs therefore potentially represent as much gain in engine temperature capability * Corresponding
author.
as was achieved in 30 years of superalloy development. However, it is necessary that the TBCs be highly reliable. One major problem is the lack of ultra-high temperature (i.e., above 1200°C) phase stability in the yttriastabilized zirconia (YSZ) thermal barrier coatings used in present-day engines. Given that current superalloys can withstand llOO”C, and if one presumes that a AT across the ZrO, layer of as much as 300°C may be possible[2], then there may be TBC applications, even in the near-term, where the outer ZrO, surface of the TBC will be at 1400°C. New TBC mat
erials having long-term phase stability at 1400°C and above are therefore critically needed for use in future high-temperature, high-efficiency gas turbines. Modern state-of-art aviation TBCs are comprised of ZrO, containing 6-8 wt.% of Y,03, a composition identified originally by NASA as giving the best thermal cycle life in burner rig tests[S]. This turns out to be the composition at which the metastable“nontransformable” tetragonal (t’) phase is formed (see the ZrO,-Y,O, phase diagram in Fig. 2) when the ceramic is quenched from the high temperature liquid or cubic phase regions[4]. This phase is described as nontransformable in that it does not undergo the catastrophic (because of a physically disruptive 4% volume change) tetragonal (t) P monoclinic phase transformation that would otherwise occur with engine thermal cycling at this Y,O,-ZrO, composition. It is also, unlike the tetragonal (t) phase, resistant to transformation to the monoclinic phase by physical stress. All evidence to date
0257-8972/96/$15.00 0 1996 Elsevier Science S.A. All rights reserved PZZ SO257-8972(96)03006-X
































Failure of EB-PVD Thermal Barrier Coatings Subjected to Thermo-Mechanical ... Properties of Rattan C... 11人阅读 5页 2.00 Numerical Simulation, ...
Oxidation and thermal fatigue of EB-PVD thermal barrier coatings on tube superalloy substrate_专业资料。维普资讯 http://www.cqvip.com Avibeolea ~c/...
4. EB-PVD process and thermal properties of hafnia-based thermal barrier coating 4. EB-PVD process and thermal properties of hafnia-based thermal ...
Effects of Shot Peening Process on Thermal Cycling Lifetime of TBCs Prepared by EB-PVD_专业资料。维普资讯 http://www.cqvip.com Avibeolea all ni ...
EB-PVD process and thermal properties of hafnia-based thermal barrier coating隐藏>> Composites: Part A 30 (1999) 483–488 Ceramic composites for thermal ...
EB-PVD process and thermal properties of hafnia-based thermal barrier coating隐藏>> letters to nature 3. Livingston, W. Radial ?lamentary structure in a...
Effects of Shot Peening Process on Thermal Cycling Lifetime of TBCs Prepared by EB-PVD_专业资料。维普资讯 http://www.cqvip.com Avibeolea all ni ...
热门文档