用于欠定条件下的盲源分离
第50卷第18期 2014年9月
机 械 工 程 学 报
JOURNAL OF MECHANICAL ENGINEERING
Vol.50 No.18 Sep. 2014
DOI:10.3901/JME.2014.18.014
基于时频分析的欠定信号盲分离与微弱特征提取
李宏坤 张学峰 徐福健 刘洪轶 练晓婷
(大连理工大学机械工程学院 大连 116023)
摘要:盲源分离对于多振源信号的故障诊断与识别是一种有效的方法,但是传统的盲源分离算法都是针对观察信号大于或等于源信号的情况,但对于观察信号小于源信号的欠定盲分离问题,这在很大程度上制约了盲源分离的实际应用。通过应用经验模式分解和时频分析对非平稳信号分析的优势,提出基于时频分析的欠定盲源分离方法进行设备微弱特征提取。对振动信号进行经验模式分解,并根据分解得到的内蕴模式分量估计源信号个数并选择最优的观察信号,将振动信号与选择的最优观察信号组成新的观察信号进行基于时频分析的盲源分离,通过对仿真信号和齿轮箱实测信号进行验证分析。并与基于独立分量分析的盲源分离算法进行对比,研究表明基于时频分析的盲源分离对混合信号具有更好的分离效果,能够较好地对微弱特征进行提取。
关键词:盲源分离;欠定信号;时频分析;经验模式分解;微弱特征提取 中图分类号:TH165
*
Investigation on Blind Source Separation for Under-determined Mixtures
Based on Time-frequency Analysis and Weak Feature Extraction
LI Hongkun ZHANG Xuefeng XU Fujian LIU Hongyi LIAN Xiaoting
(School of Mechanical Engineering, Dalian University of Technology, Dalian 116023)
Abstract:Blind source separation(BSS) is an effective method for the fault diagnosis and classification of mixture signals with
multiple vibration sources. The traditional BSS algorithm is applicable to the number of observed signals is no less to the source signals. BSS performance is limit for the under-determined condition that the number of observed signals is less than source signals. An under-determined BSS method is provided based on the advantage of time-frequency analysis and empirical mode decomposition (EMD). It is suitable for weak feature extraction and pattern recognition. The vibration signal is decomposed by using EMD. The number of source signals are estimated and the optimal observed signals are determined according to the EMD result. Then, the vibration signal and the optimal observed signals are used to construct the multi-channel observed signals. In the end, blind source separation based on time-frequency analysis are used to the constructed signals. Simulation signal and gearbox signals are used to verify the effectiveness of this method. Compared with independent component analysis, BSS based on time-frequency analysis has good performance on signal separation. It is more suitable for weak feature extraction.
Key words:blind source separation;under-determined mixtures;time-frequency analysis;empirical mode decomposition;weak feature extraction
0 前言
盲源分离可以将振动信号中的众多振动源信号分离出来,从而对机械设备进行故障诊断,是在20世纪80年代中后期发展起来的一种功能强大的信号处理方法,为机械设备多故障复合诊断提供了一种新的方法,已成为很多领域研究和发展的重要课题,同时也具有十分重要的实用价值。测试通道有限而振动源较多的信号分析,是属于欠定盲分离* 国家自然科学基金(51175057)和中央高校基本科研业务费专项资金
(DUT14ZD204)资助项目。20131004收到初稿,20140210收到修改稿
情况,因此目前采用的正定盲源分离方法不能满足实际要求,急需研究一种新的针对观察信号小于源信号的多振源信号分析方法。
现有的基于时频分析和独立变量分析的盲源分离方法都是针对正定的盲源分离,适用的都是观察信号大于或等于源信号的盲源分离问题,艾延廷[1]
等基于独立成分分析(Independent component analysis,ICA)对航空发电机和低压转子的振动信号
[2]
进行正定的盲源分离,ADEL等提出了基于时频分析的盲源分离算法。在实际的工程应用中的,由于采集通道数有限而振动源比较多,导致观察信号数目没有源信号的个数多,而形成欠定盲分离问题,
热门文档