

Trans. Nonferrous Met. Soc. China 23(2013) 128

133
Low temperature synthesis and thermal properties of
Ag Cu alloy nanoparticles
W. BHAGATHSINGH, A. SAMSON NESARAJ2
1. School of Nanosciences and Technology, Karunya University, Coimbatore-641 114, Tamil Nadu, India;
2. Department of Chemistry, Karunya University, Coimbatore-641 114, Tamil Nadu, India
Received 24 February 2012; accepted 4 September 2012
1
Abstract: Ag Cu alloy nanoparticles were synthesized by simple low temperature chemical reduction method using metal salts (acetate/sulphates) in aqueous solution with sodium borohydride as reducing agent. The chemical reduction was carried out in the presence of nitrogen gas in order to prevent the oxidation of copper during the reaction process. The alloy nanoparticles were characterized by XRD, UV-Vis, particle size analysis, EDS, TG-DTA and SEM analysis. From the XRD analysis, the crystallite sizes of the prepared samples were calculated using Scherrer formula and the values were found to be in the range of 15 nm. UV-Vis studies conform the formation of alloy nanoparticles. EDS analysis shows the presence of silver and copper in the samples. The SEM observation reveals that the samples consist of grains with average grain size up to 40 nm, and the particle size dependant melting point was studied by TG-DTA.
Key words: Ag Cu alloy nanoparticles; chemical reduction method; characterization
soldering [5].
Sn Pb alloy is a traditional material which has been 1 Introduction
used for interconnect materials for a long history.
The fabrication of materials with well defined, However, due to the inbuilt toxicity and the harm to
human health and environment, Sn Pb alloy is gradually controllable properties and structures on the nanometer
being taken out of the electronic industry in many scale coupled with the flexibility paid by intermetallic
countries. As a result, electronics manufacturers need to materials, which is referred as nanoalloys [1]. Metallic
be aware of the solder alloy choices available to them. alloys in the nanoregime reveal unique optical, catalytic,
Due to the toxicity of lead, the studies were directed electric, and magnetic properties that are widely different
towards the lead-free solders. Nowadays, attention has from those of the corresponding bulk materials [2].
been directed to lower the eutectic temperature or When two or more kinds of metals are melted together,
melting point of lead-free alloys for soldering purposes. the melting point, rigidity, conductivity, and extensibility
The utilization of metals such as tin, copper, silver, change considerably. And when it comes to nanoalloy
and sometimes bismuth, indium, zinc, antimony, and materials, new and interesting properties show up [3,4].
other metals has been investigated [6 8]. As a result, Electronic packaging is a manufacturing technology
used for electronic products. Packaging provides a many lead-free solder alloys have been proposed. The
melting point of most lead-free solders is higher than that medium for electronic interconnections and mechanical
of electric Sn Pb solder (melting point: 221 °C). This support, and solder alloys provide the electrical and
higher melting point, in turn, pushes the solder reflow mechanical connections between the die (chip) and the
(i.e., spreading of molten alloy on the contact surface) bonding pads. The selection of materials for solder alloys
temperature to over 260 °C and severely limits the is critical and plays an important role in solder joint
applicability of this metal alloy to temperature sensitive reliability [4]. A solder is a fusible metal alloy, which is
components and/or low cost organic printed circuit melted to join metallic surfaces, especially in the fields
of electronics and plumbing, in a process called boards.
Corresponding author: A. SAMSON NESARAJ; Tel: +91-422-2614301; E-mail: drsamson@karunya.edu DOI: 10.1016/S1003-6326(13)62438-3
花状纳米结构SnO_2颗粒的低温水浴合成及其光催化性能_专业资料。以SnCl2为锡源,乙醇为溶剂,六次甲基四胺、聚乙二醇400为辅助剂在低温水浴(60℃)中合成了花状...
低温共融物中金属纳米粒子催化剂的形状控制合成及其电催化性能研究_能源/化工_...江国华.王立.俞豪杰.陈涛 聚乙烯基吡咯烷酮(PVP)诱导下的Ag纳米带的制备[...
纳米Ag-Cu-In-Sn合金粉末的制备及其热分析_专业资料。利用直流电弧等离子体法成功制备了分散性较好的纳米链状Ag-Cu-In-Sn合金粉末。用X射线衍射(XRD)、透射电镜...
铁液中Al_2O_3纳米颗粒溶解和熔化的热力学研究_专业资料。与块体材料相比,纳米材料尺寸小、界面能大,导致其溶解和熔化过程的热力学不同于块体材料.从理论上...
纳米Ni颗粒增强无铅Sn-Cu-Ag复合钎料搅拌辅助低温钎焊技术_化学_自然科学_专业资料。第2 3卷第 1 O期 、,01.23 NO.1O 中国有色金属学报 The Chinese ...
纳米Mg—Ni合金吸/放氢过程的热力学性能研究_专业资料。采用机械合金化法制备了Mg-Ni合金粉末。用XRD及SEM等手段分析表征了球磨过程中的相和微观结构变化,测定了...
低温时效及微量Ag对超高强度 Al-Zn-Mg-Cu合金力学性能影响_专业资料。研究了热处理工艺对Al-12.2% Zn-2.48% Cu-2.0% Mg-0.15% Zr-0.166% Ag(合金...
电镀法制备纳米Ni—W非晶态合金的热力学分析_化学_自然科学_专业资料。第3 9卷第1期 昆明理工 大学 学报 ( 自然科 学版 ) 201 4年 2月 Journal of ...
低温球磨制备纳米晶Al-Zn-Mg-Cu合金_专业资料。利用低温液氮球磨技术制备了Al-Zn-Mg-Cu合金纳米晶粉末,并采用X射线衍射(XRD)对材料在球磨过程中的晶粒尺寸和...
负载型纳米 Pd-M(Ag,Cu)催化剂的制备 与催 化性能 53 负载 型纳米Pd—M(Ag,Cu)催化剂的 制备与催化性能 Preparation and Catalytic Property of Loaded Pd...
热门文档