CMOS CHARGE PUMPS USING CROSS-COUPLED CHARGE TRANSFER SWITCHES WITH IMPROVED VOLTAGE PUMPING GAIN AND LOW GATE-OXIDE STRESS FOR LOW-VOLTAGE MEMORY CIRCUITS Kyeong-Sik Min Is’,
Young-Hee Kim
’,Jin-Hong Ahn’,Jin-Yong Chung’, and Takayasu Sakurai’
‘Institute of Industrial Science and Center for Collaborative Research, University of Tokyo, Tokyo, 153-8505, Japan ksmin@iis.u-tokyo.ac.jp *Hynix Semiconductor Inc., Cheongju-si, 361-725, Korea’Department of Electronic Engineering, Changwon National University, Korea ABSTRACT To overcome the problems of the modified Dickson pump like NCP-2, a new pump (CCTS-I) where simple voltage doublers are cascaded in series and each of them has crosscoupled configuration is studied in this paper for possible use in low-voltage EEPROMs and DRAMs. Though this concept of cascading doublers has been previously proposed, it is firstly addressed in this paper that CCTS-I has the lower gate-oxide stress, the improved voltage pumping gain, and the better power efficiency than NCP-2 so that CCTS-1 can be more suitable for the multi-stage pump in particular at low V,,. In addition, CCTS-2 is proposed to overcome the degraded body-effect of CCTS-I without using boosted clocks when the stage number is large. 1. INTRODUCTION
gate oxide as large as 2AV. And, when the CTSZ is turned off, it should also stand a voltage stress across the gate oxide between its gate and drain as large as 2AV, arousing the circuit reliability issue due to high gate-oxide stress. Here AV is the voltage fluctuation at each pumping node and can be expressed as[4] A V= V, . cPUUP CPOUP+CS
-m I*
(1)
Multi-stage charge pumps have been investigated for many years since they can generate higher voltages than supply voltage (V,,) that are used in programming and erasing in nonvolatile memories such as EEPROMs. In addition, they can also be used in programming the antifuses for post-package failbit repair scheme in recent high-density DRAMs[I]. Most MOS charge pumps are based on the circuit proposed by J. Dickson that comprises the Diode-Configured Switches (DCS’s) and the pumping capacitors controlled by two out-of-phase clocks@ and/@)[2]. However, since its voltage pumping gain is significantly reduced with V,, decreasing, some modifications have been carried out to alleviate this gain reduction[3],[4]. One of these modified Dickson pumps is using highvoltage-driven Charge Transfer Switches (CTS’s) that do not lose the pumping voltages, as proposed in NCP-2 scheme in[4]. An example of NCP-2 with 3 stages is shown in Figure 1, where and C,,, are the Backward Control BCS’s, FCS’s, GuMP, Switches, the Forward Control Switches, the pumping capacitor, and the load capacitor, respectively. V, is the output voltage at the load. As stated earlier, using high voltage-driven CTS’s in parallel with DCS’s in Figure 1 can eliminate the sacrificial voltage loss when CTS’s deliver the generated voltages into the next nodes. How
ever, simultaneously, they should stand highvoltage stresses across their gate oxides. To see how large a voltage stress across the gate oxide is in NCP-2, let us see the CTS2, for example, in Figure 1. When the CTSZ is turned on, its gate is controlled by already established high voltage on node (3) via the FCSZ, the severe voltage stress being imposed across its
,where C, is the parasitic capacitance associated with each pumping node, f is the frequency of the pumping clocks (@ and a),& is the output current loading, and\ is the voltage amplitude of clocks (@ and D ) . If V,=Vc, and C, and 6 are negligible, the voltage fluctuation AV can have a value of yc maximally. For a practical value of AV, AV can have about 0.9 Vcc, assuming very small& and G=O.l5 GUM,. A value of C,/CPU,, is known to be in the range of 0.05-0.15 when GUM, is the oxide capacitor and about 0.05 when CUMp is the doublepoly capacitor[5]. Alleviating this high gate-oxide stress is crucial especially in the antifuse-programming charge pump used in DRAMs, since most DRAM processes do not support the dual-oxide technology with both thin and thick oxides. And, it may also be necessary even in EEPROMs with the dual-oxide process since keeping gate oxides in pumps as thin as possible is favorable to increase the channel conductance, resulting in increasing the pumping efficiency[5]. In addition, the diode configuration at the output stage in Figure 1 degrades the output voltage at the load (VJ by a voltage as large as, V (threshold voltage) of the DCS4. A new pump using doublers is presented in this paper, to overcome the problems of the modified Dickson pump as stated earlier. To know which one is more suitable for low-voltage applications, this new pump is compared with the modified Dickson pump about the gate-oxide stress, the multiplication efficiency, the power efficiency, and the layout area at the following sections 2 and 3. These comparisons are meaningful since only the modified Dickson pump like NCP-2 has been widely regarded as a suitable candidate for the multi-stage pump at low V,, applications till now[4]. 2. DESCRIPTION OF CCTS-1
As mentioned in[5], cascading two voltage doublers can generate a high-positive voltage as large as VCc+2AV and cascading three doublers can generate a voltage as large as VCc+3AV. Like this way, cascading N doublers can generate a
0-7803-7448-7/02/$17.00 0 2 0 0 2 IEEE
v - 545

热门文档