en
R3#sh run
Building configuration...
Current configuration : 1396 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R3
!
boot-start-marker
boot-end-marker
!
no logging console
!
no aaa new-model
ip cef
!
!
!
!
no ip domain lookup
!
--More-- multilink bundle-name authenticated
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
crypto isakmp policy 10
authentication pre-share
crypto isakmp key cisco address 10.1.1.2
!
!
--More-- crypto ipsec transform-set myset esp-des esp-sha-hmac
!
crypto map mymap 10 ipsec-isakmp
set peer 10.1.1.2
set transform-set myset
match address 100
!
!
!
!
!
interface Loopback0
ip address 1.1.1.1 255.255.255.0
!
interface FastEthernet0/0
no ip address
shutdown
duplex half
!
interface Serial1/0
no ip address
shutdown
serial restart-delay 0
--More-- !
interface Serial1/1
ip address 10.1.1.1 255.255.255.252
serial restart-delay 0
clock rate 64000
crypto map mymap
!
interface Serial1/2
no ip address
shutdown
serial restart-delay 0
!
interface Serial1/3
no ip address
shutdown
serial restart-delay 0
!
interface FastEthernet2/0
no ip address
shutdown
duplex half
!
ip route 2.2.2.0 255.255.255.0 10.1.1.2
--More-- no ip http server
no ip http secure-server
!
!
!
logging alarm informational
access-list 100 permit ip 1.1.1.0 0.0.0.255 2.2.2.0 0.0.0.255
!
!
!
!
!
control-plane
!
!
!
!
!
!
gatekeeper
shutdown
!
!
--More-- line con 0
stopbits 1
line aux 0
line vty 0 4
!
!
end
R3# sh ipsec sa
^
% Invalid input detected at '^' marker.
R3# sh ipsec sa ipsec sac ipsec sar ipsec say ipsec sap ipsec sa[ ipsec sat ipsec sa ipsec sa ipsec sa t ipsec sao ipsec sa ipsec sa
interface: Serial1/1
Crypto map tag: mymap, local addr 10.1.1.1
protected vrf: (none)
local ident (addr/mask/prot/port): (1.1.1.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (2.2.2.0/255.255.255.0/0/0)
current_peer 10.1.1.2 port 500
PERMIT, flags={origin_is_acl,}
#pkts encaps: 19, #pkts encrypt: 19, #pkts digest: 19
#pkts decaps: 19, #pkts decrypt: 19, #pkts verify: 19
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0
#pkts not decompressed: 0, #pkts decompress failed: 0
#send errors 0, #recv errors 0
local crypto endpt.: 10.1.1.1, remote crypto endpt.: 10.1.1.2
path mtu 1500, ip mtu 1500, ip mtu idb Serial1/1
current outbound spi: 0xC357E725(3277317925)
inbound esp sas:
spi: 0xE959C324(3914973988)
transform: esp-des esp-sha-
IPSec-VPN-配置详解_IT/计算机_专业资料。IPSec VPN配置过程IPSec VPN 配置详解小型企业少量的分公司, 通道。 小型企业少量的分公司,配置点对点 IPsec VPN 通道。...
2. 3. 理解 VPN 的概念及作用 掌握 IPsec VPN 的配置流程 掌握 Site-to-Site IPsec VPN 的配置 二、基本技能实验内容、要求和环境:总部 192.168.1.0/24 ...
华赛防火墙ipsec-vpn配置示例_计算机硬件及网络_IT/计算机_专业资料。华赛防火墙ipsec-vpn配置示例配置采用 IKE 方式建立 SA 示例(预共享密钥)组网需求如图 7-2 所...
IPsec-VPN 客户端安装及配置指南 客户端安装及配置指南 1.双击 IPSEC 安装包内的 SETUP.EXE 2. ,如图,点击 NEXT 2.下一步 点击 YES 3.下一步 选择安装...
PIX525—IPSEC-VPN 配置 PIX525—IPSEC-VPN 配置实验拓扑: -1- by 风行无际 实验要求: 在 PIX525 上进行配置,要求内网 PC2 能 telnet 登入到 PIX525 上;...
IPSec VPN配置-实验一_计算机软件及应用_IT/计算机_专业资料。IPSec VPN基本配置-实验一,适合初学者及进阶者实验名称: 实验要求的环境: 第三章 IP Sec VPN(一)...
IPSec的VPN配置实例及说明_IT认证_资格考试/认证_教育专区。vpn的简单配置IPSec 的 VPN 配置实例及说明 1、 Router(config)#crypto isakmp policy 1 //policy 1...
1-8 1 IPSec VPN 配置向导 1.1 概述 IPSec VPN 策略配置向导提供了对 IPSec VPN 的快速配置功能,可以帮助用户完成 IPSec VPN 相关参数的配置。关于 IPSec 和...
IPsec VPN配置命令详解_计算机软件及应用_IT/计算机_专业资料 暂无评价0人阅读0次下载举报文档 IPsec VPN配置命令详解_计算机软件及应用_IT/计算机_专业资料。...
热门文档