MATERIALS ISSUES FOR TURBINES FOR OPERATION IN ULTRA-SUPERCRITICAL STEAM
I.G. Wrighta, P.J. Maziasza, F.V. Ellisb, T.B. Gibbonsc, and D.A. Woodfordd
ABSTRACT
Coal-fired supercritical-steam power plants are currently operating with steam temperatures at the inlet tothe high-pressure turbine close to or slightly above 600°C. The use of recently-developed martensitic-ferritic steels is expected to allow this temperature to be raised to 620°C, which probably represents theinherent limit of capability of these advanced steels. Further increases in temperature capability willrequire the use of Ni-base alloys, and efforts in this direction have been pioneered in Europe where thereare plans to build a plant operating on steam at 700°C. In the U.S., there is a significant effort aimed atqualifying alloys that could be used for tubing and piping to deliver steam at 720/760°C. In this paper,the technical and business considerations involved in determining and prioritizing the materials needs forturbines operating under these ultra-supercritical steam conditions are discussed.
BACKGROUND
It is widely recognized that, because of the very large role that coal plays in power generation, efforts toreduce overall CO2 emissions will, of necessity, involve efforts to find cleaner ways in which to use coal.Removing carbon from coal before or after combustion introduces costs that seriously detract from thecompetitiveness of that power generation process. If the efficiency of the overall cycle were to beimproved, however, less CO2 would be produced for each unit of electricity generated.
In typical U.S. supercritical steam practice, steam is delivered to the turbine at temperatures up to 566°Cand at a typical pressure of 238 bar. There is experience in the U.S. of operation at higher steamconditions: Philo Unit 6 of American Electric Power (started up in 1957) operated with steam at621°C/310 bar, with two reheats to 566°C1. In addition, Eddystone Unit 1 of the Philadelphia ElectricCompany (started up in 1961) operated with steam conditions of 649°C/340 bar, with double reheats to566°C2. Both were relatively small units by modern standards, 125 and 325 MW, respectively; the sizewas essentially determined by the size of the austenitic steel high-pressure rotor that could be made at thetime3. The steam turbines were manufactured by General Electric (GE) and Westinghouse, respectively.Problems were experienced with these early, pioneering units, some of which were materials related, andthese contributed to a decision to derate to less ambitious steam conditions to improve reliability.Subsequent supercritical plants in the U.S. employed steam conditions which are typically 541-566°C/238bar. As of 1986, some fifteen percent of the U.S. fleet of operating steam power plants used asupercritical steam cycle, and these are mostly 1960s-1970s-vintage units4. The turbines installed in theU.S. supercritical fleet were manufactured principally by GE and Westinghouse, with some from theBrown Boveri Company.
Elsewhere, there has been a gradual push for the use of steam conditions in advance of those generallyused in the U.S. As an example, the Avedøre Unit 2 Power Station of the SK Power Company inDenmark, which started commercial operation at the beginning of 2001, operates with a main steama Oak Ridge National Laboratory
b Tordonato Energy Consultants
c Consultant to ORNLd MPa Inc.
Woodford, “Materials Issues for Turbines for Operations in Ultra-Supercritical Steam,” Proceedings of the 29th Internat. Conf. on Coal Utilization and ...
Materials for Boilers in... 22页 1财富值 ultra...Ultra-Supercritical (USC) units under operation ...ultra supercritical boilers and steam turbines, electric...
for single materials while incinerators must ...as electrical power by utilizing steam turbines. ...Supercritical fluids refer to the fluids that are...
Performance Analysis and Retrofit on 350-MW China-Made Supercritical Steam Turbines_专业资料。 今日推荐 157份文档 2015国家公务员考试备战攻略 ...
热门文档