文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 医药卫生 > WHO-ongoing stability test
侵权投诉

WHO-ongoing stability test

Ongoing studies are intended to prove that, over the period of its labelled shelf life and under‘real life conditions’, the product remains of the quality defined in the authorisation/registration documents. Stability studies done for registration solely provide a‘snap-shot’. Adverse effects such as changes in manufacture and the supply chain (even those not on a variation level) should be identified by ongoing studies. However, this procedure also implies that the test protocol can be adjusted at any time to the current situation. The stability protocol does not necessarily have to comply with the ICH stability testing guidelines. POTENTIAL SAVINGS– REALISATION AND PITFALLS Item 6.28 of the EU GMP Guidelines specifically states that the protocol for the ongoing stability programme may differ from that of the initial long-term stability protocol (3), giving a reduction in the frequency of testing as an example. If it has been shown that a test parameter is not critical, for example during the course of commitment (follow-up) studies or later in ongoing studies that have already been performed, th

e frequency of testing may be reduced. A given example shows that, overall, there is a possible reduction in the required frequency of testing of about 50 per cent or even more (see Table 3). It should be noted that at the end of the shelf life, all the test parameters should be checked again (in this case t60), in order to prove stability over the entire storage life. If the product is manufactured in different strengths (same API with similar matrix) and pack sizes, the‘bracketing’ recommendations can be applied (4). If there are more than two sizes for any parameter, this provides for only the extremes to be tested (see Table 4). This example shows the requirements in the guidance. Assuming an identical bulk product, then if the exemplary product above is packed in blister packs of 10 tablets, each with identical primary packaging material, the effect of secondary packaging– for example, different secondary packaging for different foreign markets– does not have to be taken into account. Testing of only one pack size would therefore be sufficient. The same applies to multi-dose containers, where only the most sensitive size of container would have to be tested on a‘worst case scenario’ basis. In the latter (ideal) example, the number of tests could be reduced from nine to two, with corresponding costsavings. However, consideration of the individual case is always important. It may be necessary, for example, for the first batches to be tested in accordance with the full protocol in order to provide sufficient data for trend analyses. The combination of ongoing studies with follow-up (commitment) studies is often discussed. It should be emphasised here that, in principle, the data that are

Table 2: Selection of stability-limiting parameters. Decision should be made on the basis of existing data Less critical parameters Capsules and tablets Organoleptic and physical tests, uniformity of mass and content, disintegration and dissolution, microbiological quality Organoleptic tests, uniformity of dosage, density, pH-value, preservation, microbiological quality Organoleptic tests, uniformity of dosage, density, pH-value, preservation More critical and essential parameters Assay and impurities

Liquids (for oral use)

Assay and impurities

Sterile solutions (Ophthalmica, Parenteralia)

Assay, impurities, sterility and particles

Table 3: Protocol with reduced frequency of testing for an ongoing study (solid formulation): T= Test, (T)= Test optional, o= designated testing, dossier (2), (3) omitted Test Organoleptic Mass uniformity Resistance to crushing Dissolution test Identity Assay Purity Microbiological quality 25ºC/60% rh 30ºC/65% rh 40ºC/75% rh t0 T T T T T T T T T t3 (T) o o o o o (T) o t6 (T) o o o o o (T) o o t9 (T) o o o o o (T) o t12 (T) o (T) T T T T T o t18 (T) o o o o o (T) t24 (T) o (T) T T T o T t36 (T) o (T) T T T o T t48 (T) o (T) T T T o T t60 T T T T T T T T -

generated in follow-up studies can also be used for

review, as mentioned in sub-item vii in the PQR. Conversely, however, this means that tests must cover the full protocol in the dossier. Savings, such as those discussed above, are hardly possible in this case. If it was agreed in the post-marketing commitment that, after launch, one batch per year would be tested for three years for the follow-up study, then the additional (ongoing) tests could be saved for three years. As usual, analyses for the release of a product batch can also be used as starting values for ongoing studies, but possible differences in the specifications have to be observed. Thus, further ongoing testing does not start until a year after the start of storage. It is also recommended that production and hence starting dates should, if possible, be in the same period of the calendar year. As a result, in subsequent years there will be further synergies as a result of parallel testing. STEPS AFTER TESTING Suitable data analysis procedures that allow not only retrospective but also prospective evaluation have to be established. The EU GMP Guidelines require that, at the individual test times, it must be stated whether it can be assumed that, for example, the active substance content Table 4: Example of bracketing, (T= Test; o= Test omitted), solid formulation Strength 50mg 20 tablets 50 tablets 100 tablets T o T 75mg o o o 100mg T o T

Innovations in Pharmaceutical Technology

79

WHO-ongoing stability test

上一页第2页

你可能喜欢

热门文档

相关文档

  • DYNAMIC STABILITY TEST -- Calculate Formula - UL108...

    DYNAMIC STABILITY TEST -- Calculate Formula - UL1083 油炸锅动态稳定性测试计算表_表格类模板_表格/模板_应用文书。DYNAMIC STABILITY TEST -- Calculate Formula...

  • EE Voltage Stability Test SOP(电压稳定性测试作业规范)

    EE Voltage Stability Test SOP(电压稳定性测试作业规范)_信息与通信_工程科技_专业资料。EE Voltage Stability Test SOP(电压稳定性测试作业规范)ISDDQAEE...

  • Robust Hurwitz and Schur Stability Test for Interva...

    question to be discussed is whether the 2-D face stability test for interval matrices can be used to the stability test for the polytopes of matrices?...

  • 【论文】Test Stability of Uster Advanced Fiber Info...

    Test Stability of Uster Advanced Fiber Information System(AFIS)_专业资料 暂无评价

  • Stability 5

    ? ? The test results generated by the stability studies will be evaluated ...Allow personnel who are more remotely involved in the daily maintenance of ...

  • fishhook_test

    www.Corrsys-Datron.com NHTSA Fishhook test www.Corrsys-Datron.com NHTSA Rollover Stability Steering wheel angle, roll stability triggered Steering wheel ...

  • 试验翻译

    test 酚含量试验 phenol content test 灰分含量试验 ash content test 储存稳定度试验 storage stability test 车辙试验 wheel rutting test 马歇尔稳定度试验 Marshall...

  • Pre-test List, quotation

    Test Product Shell Shock Experiments Hi-pot test Normal Temperature Test Module Defect Test Stability Test Drop Test Robustness of Terminations Test Aging ...

  • MZM-new-product-advisory1

    Kemgard MZM New Product Advisory SIGNIFICANT IMPROVEMENT IN SMOKE SUPPRESSION AND DYNAMIC STABILITY FOR RIGID PVC SYSTEMS KEMGARD MZM PROVIDES SUPERIOR SMOKE SUP...

  • ...on Dutasteride and Development of a Stability-In...

    The current drug stability test guideline Q1A (R2) issued by the International Conference on Harmonization (ICH) [7] suggests that stress studies should ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email