ONPRESS (HDI ) Laser vias、 Micro Blind vias (mechanical drilling) of ability 、 以下填写 羅苑填写 以下填写由R&D羅苑填写 羅苑填 Laser vias 100µm or 150µm other diameters→最小能力100um,如>150um以上可采用 mechanical drilling成本較低,制作效率較高。
( R&D: luo yuan ) :
Micro Blind vias (mechanical drilling)
Hole diameter (after drilling)
200µm?→我公司可做>150um以上mechanical drilling。
Pad diameter = Hole diameter +單邊焊環寬度X2
Pad on outerlayer: x =80um(單邊PAD) Pad on innerlayer (landind pad): x =100um(單邊PAD)
單邊PAD80um--min
holer100um--min
260um---min (1)大於此能力我公司可制作!(采用ccd平行暴光) With the smallest hole and the smallest pad on the outerlayer, what is the minimum annular ring you can guarantee (take in consideration the tolerance of drilling and of the alignment of the exposure film on the outerlayer) 80um--min
→※我公司要求最小單邊PAD有0.08mm。
PAD holer直徑100um
Aspect ratio (diameter:depth)
1:0.75 →※Aspect ratio diameter:depth此能力能達到我司HDI,Laser viasPTH之能力為≦1!
A B B:A≤1:1
(1)Laser vias最小孔徑0.1mm,孔深B與直徑A之比例:≦1:1; (2)沉銅次數:≦φ0.15mm時,PTH兩次; (3)PTH後全板電鍍時采用射流電銅缸一次性電夠120min,10um-
Tolerance on the depth of the hole
not applicable
→※孔深度一般要求達到Laser vias需要連接 Copper foil層的2-5um;
Stack-up (preferable)
RCC Core …. Core RCC (What is the thickness of Cu, C-stage epoxy and B-stage epoxy?)
Indicate a typical stack-up.Indicate the distance you need between first and second innerlayers (core thickness) to avoid shorts due to the drill bit.---內層第一層與第二層中心厚 度的距離最薄可做到30um;最厚可做到100um;
Stack-up (also possible)
Copper layer (max 1/2 OZ) 1 sheet prepreg 106 or 1080 (2 sheets also possible) Core …. Core 1 sheet prepreg 106 or 1080 (2 sheets also possible) Copper layer (max 1/2 OZ) ※以每種新工藝新定單交貨數量的一倍預投;
此類似組合不可行,以超我司HDI Aspect ratio( diameter:depth),PTH及全板電鍍無法做到, 如單張FR-4prepreg≦1080或100um以下(max 1/2 OZ)我司有能力做到; Layer1 Layer2 Copper foil 1/2OZ prepreg≦1080或100umprepreg
Core Layer3 Layer4 prepreg≦1080或100umprepreg Copper foil 1/2OZ
Number of pieces (or square meters) you produce with each technologies
According to your experience, which is the preferable technology (better yield, less problems during drilling / plating, …)
※根據我公司HDI之經驗來看采用Micro Blind vias (mechanical drilling)的生產能力效果較好,制作周期較短效率較高;兩者 相比,如客戶質料無特殊要求主推---Micro Blind vias (mechanical drilling)制作; ※可以做到綠油塞Laser vias孔與Micro
Blind vias (mechanical drilling)但效果較一般,穩定系數較低在二次沉電銅時 孔內較容易藏藥水;主推---普通樹脂或含銅樹脂;
⊕PAD環綠油較難處理二次沉
Have you got a technology to fill the vias in order to have via in solderpad ?
⊕綠油塞兩種以上制作方式的 Micro Blind.holer都易藏藥

Laser resolidification of Zn_IT/计算机_专业资料。Laser remelting experiments were performed by a 1.0kW continuous CO2 laser to investigate the rapid ...
ROFIN PAGE 13 F Focus on Fine Solu ns s e ution The mark of excel ce k e llenc Lasers with high beam quality and stability are needed Laser ...
penetrating nature of plasma and the ability to precisely control the process...可以提高层间结合力 Forming blind vias requires the use of laser drilling ...
Int J Adv Manuf Technol (2011) 52:977–987 DOI 10.1007/s00170-010-2791-3 ORIGINAL ARTICLE Fibre laser welding of dissimilar alloys of Ti-6Al-4V ...
Optical and Laser Characterization of 2at% NdYAG transparent ceramic_材料科学_工程科技_专业资料。Optical and Laser Characterization of 2% Nd:YAG Ceramics ...
vias are drilled using a UV laser after RCC lamination and are metalized ...mold embedded wafer have been intensively evaluated on their process ability....
LASER World of PHOTONICS 2011圆满谢幕——未来核心光电技术的盛宴_专业资料。·观众人数增长超过8%,达27500人·观众国际化程度更高:来自于80个国家·增长领域:...
Disruption Mitigation Using Laser Ablation of High-Z Impurities in HL-1M Tokamak_专业资料。维普资讯 http://www.cqvip.com 12 DirpinMiiainUsngLae .5suto ...
Laser ablation of electronic materials_互联网_IT/计算机_专业资料。烧蚀激光...The ability to nondestructively analyze unprepared samples makes LIBS a highly...
Novel progress in laser welding of dissimilar materials 隐藏>> 维普资讯 http://www.cqvip.com Nvlrgesi srligo oe ors le dn fpnaweds irtrl sm eisii maala...
热门文档