WARNING:
The example configuration below was created from a factory default configuration on the HP ProCurve 5300XL Switch. The first 3 commands in the sequence of CLI commands given below will first reset the switch back to factory default settings. We recommend saving your current configuration if necessary. Otherwise, skip the first 3 commands.
NOTES:
1. The interface port numbers (e.g. interface a1) and the IP address (e.g. 10.10.10.2) may differ in your network, so adjust these values accordingly.
2. The HP ProCurve Switch 5300XL Series (e.g. HP 5304XL), type of module(s), and software version number below may not accurately reflect the device(s) you are configuring.
3. The area 0.0.0.0 command is used to assign the 5300XLSwitches to the single backbone area. 4. The ip ospf area 0.0.0.0 command is used to assign the individual interfaces to the OSPF area. 5. In the example below for Switch B, as soon as the redistribute connected command is issued for a given routing protocol, ALL connected routes are advertised within that routing protocol. The restrict 198.168.40.0/24 command is used in order to keep this directly connected network (e.g. VLAN 40) from being advertised through OSPF to Switch A.
6. In the example below, the redistribute connected command is needed in order for Switch A to learn (via OSPF) the directly connected network (e.g., the 30.30.30.0 network) on Switch B and vice versa. By default the Switch 5300XL will not advertise directly connected OSPF networks. By default the Switch 5300XL will advertise directly connected RIP networks.
7. The configuration examples below were created on software version E.06.01.
HP+procurv系列交换机配置手册_计算机硬件及网络_IT...OSPF restrict list IP Address Mask --- ---198...(ospf)# area 0.0.0.0 Switch_A(ospf)# ...
HP交换机配置手册 procurv交换机配置手册 HP2524 HP...OSPF restrict list IP Address Mask --- ---198...(ospf)# area 0.0.0.0 Switch_A(ospf)# ...
HP procurv交换机配置手册2524_lacp_IT/计算机_专业资料 暂无评价0人阅读0次下载举报文档 HP procurv交换机配置手册2524_lacp_IT/计算机_专业资料。...
procurv交换机配置手册-完善版_IT/计算机_专业资料。hp procurv 交换机配置...OSPF restrict list IP Address Mask --- ---198.168.40.0 255.255.255....
HP交换机配置命令_IT/计算机_专业资料。HP 交换机配置命令 1.命名 hostname 7-West-4F-2510 2.设置管理 IP vlan 1 ip address 192.168.41.123 255.255....
HP交换机配置命令_IT/计算机_专业资料。HP交换机vlan配置命令HP 交换机配置命令 1.命名 命名 hostname Guests_network 2.设置管理 IP 设置管理 vlan 1 ip ...
HP交换机基本命令配置_IT/计算机_专业资料。HP交换...OSPF 的配置如下图所示为两台交换机之间运行 OSPF ...(ospf)# area 0.0.0.0 Switch_A(ospf)# ...
海思曼和HP交换机配置方法_计算机硬件及网络_IT/计算机_专业资料。海思曼交换机配置方法 HP 交换机配置 HP 光纤存储交换机 用户:admin 出厂密码:password 出厂 IP...
HP交换机配置手册(免费下... 44页 免费 hp交换...OSPF ......(ospf)# area 0.0.0.0 Switch_A(ospf)# redistribute connected Switch_A(ospf)# vlan...
重启交换机 test(config)#reload 6、清空配置 test(config)#erase startup-config 7、配置console密码 (1)、配置明文密码 test(config)#line console 0 test(...
热门文档