文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 电子/电路 > A Novel Crossed Traveling Wave Induction Heating System a
侵权投诉

A Novel Crossed Traveling Wave Induction Heating System a

A Novel Crossed Traveling Wave Induction Heating System a

ANSYS 2011中国用户大会优秀论文

A Novel Crossed Traveling Wave Induction Heating System and Finite Element Analysis of Eddy Current and Temperature Distributions

S. L. Ho, Junhua Wang, Student Member, IEEE, W. N. Fu1, and Y. H. Wang 2

Department of Electrical and Engineering, The Hong Kong Polytechnic University, Hong Kong

2

Joint Key Laboratory of Electromagnetic Field and Electrical Apparatus Reliability, Hebei Univ of Technology, Tianjin, China

1

11

A novel crossed traveling wave induction heating (C-TWIH) system for heating thin industrial strips is proposed and its finite element method (FEM) simulations are reported. Compared with a typical traveling wave induction heating (TWIH) device, C-TWIH has more uniform and concentrated eddy current density distributions. This is because the C-TWIH system exploits a three-phase induction heater with crossed yoke arrangement, and the magnetic fluxes generated by each phase are interacting and complementing each other to compensate for the weak magnetic areas of each phase. Temperature distribution and variation of the C-TWIH system is also characterized. The fabricated novel model has a temperature range from 251°C to 270°C and its undesired temperature non-uniformity is reduced by 43% compared with those in typical TWIH devices.

Index Terms—Eddy current, finite element method, temperature distribution, transverse flux, traveling wave

I. INTRODUCTION

has attracted a lot of attentions from researchers and practitioners. Traditional longitudinal method and single- phase transverse flux technology are inadequate to meet the ever increasing demand on quality performance in regard to temperature uniformity on the work strips, especially on thin and long strips. Among the multiphase systems being developed recently, the traveling wave induction heating (TWIH) process is potentially very promising and attractive. Unlike the longitudinal or the single-phase transverse flux heaters, TWIH is energized with three-phase windings. Parametric analysis is used to assess the key parameters (transmission efficiency of electricity to the work-piece, power factor, etc.). TWIH is intrinsically more suitable than its single phase counterpart in the provision of uniform thermal density on the work strips [1]. Indeed, three-phase induction heaters not only have the same advantages as their single-phase counterparts, they can produce more uniform temperature distributions and operate with less industrial noise and vibration. For operations in which the electromagnetic force may increase significantly and the heating parameters could change as the temperature rises, the advantage of TWIH is even more significant.

Despite of the wealth of industrial potential applications of TWIH, there are few reports in the literatures on this important technology when compared to those on longitudinal induction heating and transverse flux induction heating (TFIH) systems, even though there are some dedicated analytical studies and numerical methods on TWIH systems [2-5]. In fact, prior studies only introduce some unrealistically over-simplified and impractical

T

HE INCREASING demand for industrial furnace heaters

assumptions using, for example, a current sheet on the yoke without slots as the model.

A novel design for a crossed traveling wave induction heating (C-TWIH) system is proposed to address the inhomogeneous eddy current density which dominates the temperature distribution on the surface of work strips. Finite element method (FEM) is used to calculate the eddy current and temperature distributions. Simulation results of the novel C-TWIH system are presented and compared with those of typical TWIH and TFIH systems to showcase its better performance.

II. THE PROPOSED STRUCTURE OF C-TWIH

The schematic of a typical heater configuration is shown in Fig. 1 (a). There are two linear inductors on the opposite sides of the strip and twelve slots along the direction of the movement. There is a relatively large airgap between the inductor and the strip due to the thickness of the interposing

A Novel Crossed Traveling Wave Induction Heating System a

refractory materials.

(a)

A Novel Crossed Traveling Wave Induction Heating System a

(b)

第1页

你可能喜欢

热门文档

相关文档

  • Carbanions ...

    Induction 3. Hybridization style 4. Aromaticity ?...(HOCH2)4C Pentaerythritol Crossed Cannizzaro ...2 COCO2Et hydrolysis CO2H PhCH COCO2H heating CO2...

  • Free.Energy_Induction Heating System With Transisto...

    Free.Energy_Induction Heating System With Transistor Inverter_信息与通信_工程科技_专业资料。Free.Energy_Induction Heating System With Transistor Inverter今日...

  • ...resonant inverter for induction heating

    Control System Design And Small Signal Analysis Of APWM Resonant Inverter For Induction Heating M.HELAIMI Dept. of electrical engineering, university of Hassib...

  • ...transfer of induction heating of a slab

    the 3-D eddy current field problem coupled to the steady-state heat transfer in an inductor-slab system that is part of an induction heating process. ...

  • ...Induction Heat to Line Heating Technolo

    Feasibility Research on Application of a High Frequency Induction Heat to Line Heating Technolo_专业资料。JMaieSiApl21 1:5—6 .r c.pf0 1 4644n1 0DOI...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email