文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > 2.45 GHz end-loaded dipole backed by a high impedance surface
侵权投诉

2.45 GHz end-loaded dipole backed by a high impedance surface

2.45 GHz End-Loaded Dipole Backed by a High

Impedance Surface

David Cure*(1), Sergio Melais (1), Thomas Weller (1), Paul Herzig(2) and Robert Roeder(2)

(1) University of South Florida, Tampa, FL, 33620, doc.guandang.net

(2) Raytheon Systems, St. Petersburg, FL, USA An end loaded planar open sleeve dipole (ELPOSD) antenna over an electromagnetic band gap (EBG) high impedance surface is presented. An ELPOSD consists of a printed dipole with two parasitic elements (sleeves) along its sides and capacitive loading at the end. This antenna is fed from beneath the ground plane by live vias connected to a microstrip to coplanar strip balun. The EBG structure is based on the Jerusalem Cross geometry and is sandwiched between two 1.27 mm-thick substrate layers, resulting in a total antenna thickness (excluding the feed layer) of ~λ/50. Measured performance of the antenna demonstrates a bandwidth of 30 MHz at 2.45 GHz, with a gain of ~3.5 dB.

Introduction Herein a low-profile planar antenna operating at 2.45 GHz with uni-directional radiation is presented. The goal of this effort was to establish a baseline approach for realizing a flexible antenna with moderate bandwidth that can be used in applications such as body-worn sensors. For electromagnetic sensing, e.g. in the case of radiometric sensors, reduction in backside radiation is important in order to maximize the detection sensitivity. Accordingly, a design incorporating a backing ground-plane is appropriate. Furthermore, in this particular effort, the ability to tune the operating frequency is desirable as this allows real-time adjustment of the sensing depth. For this reason, the architecture has been conceived with the aim of facilitating eventual integration of varactor-based tuning.

Among the choices for antenna elements satisfying the above criteria are various forms of microstrip patch antennas. Standard, single-layer patches are typically narrow-band [1] and tuning approaches usually involve devices that are exposed on the outer surface [2], contrary to the embedded solution that is desired in this work. Multi-layer patches may offer instantaneous bandwidth covering the frequency range of interest [e.g. 3] however the thickness conflicts with the desire to achieve a flexible, low-profile design.

The approach taken in this work was to integrate an end-loaded planar open sleeve dipole (ELPOSD) into a multi-layer substrate that includes a back ground-plane and an intervening high-impedance, electronic band-gap (EBG) layer. The ELPOSD is naturally broad-band, typically ~25% bandwidth, and compact in size. The Jerusalem Cross Frequency Selective Surface (JC-FSS) geometry was selected for the EBG layer, due to its wide angular stability and the potential for convenient frequency tuning and substrate thickness reduction. Previous authors have investigated the combination of an ELPOSD with patch-type electronic band-gap (EBG) layers [e.g. 4, 5].

Antenna Design and Performance

The ELPOSD antenna design consists of a printed dipole that is loaded with two parallel sleeves, and has parasitic capacitive loading at the ends of the dipole arms; the loading

978-1-4244-4968-2/10/$25.00 ©2010 IEEE

第1页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email