Products Development based on the Technology of Design for Manufacturing and Assembly ZUO Shilun
Products Development based on the Technology of
Design for Manufacturing and Assembly
ZUO Shilun
Chongqing University of Science & Technology, Chongqing 401331,China
zuoshilun@126.com
Abstract
The technology of Design for Manufacturing (DFM) and Design for Assembly (DFA) presents a challenge to the traditional product development model, it is an important part of the concurrent engineering technology. DFA mainly consider simplistic design, minimize flexible parts and interconnections, design for ease of assembly by utilizing simple patterns of movement and minimizing the axes of assembly, design for efficient joining and fastening. DFM mainly include standardize design, design for ease of fabrication, design within process capabilities and avoid unneeded surface finish requirements. The application of DFMA must consider the overall design economics. It must balance the effort and cost associated with development and refinement of the design to the cost and quality leverage that can be achieved. This paper studies nozzle design of the static mixer, and support shaft design of the tilting slot by comparing the Traditional Design (TD) with the DFMA. According to effectiveness analysis of the design results, it confirms that DFMA play an important role in reducing time and cost of product development.
Keywords: Product development, traditional design, Design for Manufacturing and Assembly,
Integrated part, Time and cost reduction.
1. Introduction
In traditional product development model, products have been designed that might not be produced, design process is often out of touch with the manufacturing process, it makes manufacturability, maintainability, and assemblability of the product be poor, leads to large changes in the whole design phase. Product development cycle, costs and product quality are difficult to guarantee, or even a large number of design can not be put into production, and other consequences, which results in a huge waste of human and material resources. Products have been released for production that their prototypes were built and adjusted only by highly skilled technicians. There is a famous theory that the product design expenses accounts for only 5% of total product costs, but it affects 70% of the whole cost of products[1]. For a new product, cost and development cycle are the key factors in the success or failure of the design. So an effective product development must surpass the traditional steps of implementing and acquiring product and process design technology.
The DFMA (Design for Manufacturing and Assembly) presents a challenge to the traditional product development model[2]. The DFMA technique is a unified title of the DFX(Design for “X”), it is an important part of the concurrent engineering. It has a very rich content, it involves in manufacturing and product development , assembly, testing, maintenance, and disposal various stages of processing, etc.. At every stage of the design, employing DFMA ideas and related tools, designers can obtain design information that how to choose material, select process and parts cost analysis, and as so on. It is a new, simpler, more effective approach to product development, which provides these enterprises with a practical way to reduce production costs, shorten product development cycles, improve enterprise efficiency[3]. The DFM refers to products designed meeting the needs of manufacturing, good manufacturability makes products be at the lowest cost, shortest time, and highest quality. This indicates the great leverage that the DFM can have on a enterprise's success and profitability[4]. However, the application of the DFM must consider the overall design economics. It must balance the effort and cost associated with development and refinement of the design to the cost and quality leverage that can be achieved. That is to say, greater effort to optimize a products design can be justified with higher value or more production. Producibility is improved by incorporation of the DFM practices. The DFM requires the designer start their work by considering various design concept alternatives early in the process. Of course, the alternatives must be evaluated against the DFM objectives, and design tools are used to develop a more mature and producible design before release for International Journal of Advancements in Computing Technology(IJACT) Volume 6, Number 3, May 2014132
Toy development and design based on the needs ...users’ needs are sources of many new products....[m].liaoning science and technology press, 2008....
will be described based on key development modules...design, manufacturing and assembly, selection of ...the technology certification; Test representing the ...
Design for Manufacturing ? Design for Six Sigma ...Faster development of new products ? Products that...and mfg capabilities New technology and innovation ...
Design for Manufacturing_英语学习_外语学习_教育...Analysis tools – group technology and mass ...? ? ? Development Time Development Cost Product ...
Design for X (DFX) Basics A knowledge-based approach for designing products...technology required to produce the product, and potential new manufacturing ...
development of information technology_经济/市场_经管...design, manufacturing, procurement and assembling of...products and parts production greatly improved and ...
of design information data, the development of ...technology, there are abundant of material products...[1] Functional Functional features Manufacturing ...
Service Process Design (6)Choice of Technology? ...Time Manufacturing III PRODUCT AND SERVICE DESIGN ...? Demonstrate how the development of products can...
4 TQM - University of Michigan 2 Design Quality Into Products Pat Hammett ...development functions are design engineering, process engineering, manufacturing ...
technology, preferences, and regulations) into information about products and...development teams and design for manufacturing guidelines) have been created, ...
热门文档