Comparison Of Failure Criteria For Jointed Rock Masses 节理岩体破坏准则比较
COMPARISON OF FAILURE CRITERIA FOR
JOINTED ROCK MASSES
G. Madhavi Latha¹, T.G. Sitharam²¹)Indian Institute of Science, Bangalore
madhavi@civil.iisc.ernet.in
²) Indian Institute of Science, Bangalore
sitharam@civil.iisc.ernet.in
Abstract: This paper compares two different failure strength criteria for rock; the popular non-linear Hoekand Brown failure criterion and a simple non-linear failure criterion recently proposed by Ramamurthy.Equivalent continuum analyses of jointed rock masses have been carried out using program FLAC with eachselected failure criterion. The constitutive behaviour of the rock mass is represented by Mohr-Coulombmodel in both cases, which is modified by applying the respective failure criterion using special subroutines.Numerical analysis of triaxial tests on intact and jointed rocks has been carried out first and results have beenvalidated against data from experiments. Further, a case study of an underground power cavern has beenanalysed using both of these failure criteria and the displacements obtained from the analyses were comparedwith the field measurements. This study brought out the relative merits and demerits of the two failurecriteria when applied to the field problems and confirmed that the simple failure criterion proposed byRamamurthy could be applied with confidence for the analysis of jointed rock masses.
Keywords: Equivalent continuum, failure criterion, joint factor, numerical analysis, rock mass, simulation
1.INTRODUCTION
Reliable estimation of strength and modulus ofrock mass is very important for studying thebehaviour of open and underground excavations,rock slopes, arch dams and bridge piers. A betterunderstanding of the strength and modulus of rockmasses makes it possible to control stabilityproblems in jointed rock masses. The propertiesof the intact rock between the discontinuities andthe properties of the joints themselves can bedetermined in the laboratory, where as the directphysical measurements of the properties of therock mass are very expensive and timeconsuming. For determining the rock massproperties indirectly, a theory needs to beestablished and tested in some independent way.A number of experimental studies have beenconducted both in field and in the laboratory tounderstand the behaviour of natural as well asartificial joints. In-situ tests have also been carriedout to study the effect of size on rock masscompressive strength. Laboratory studies showthat many different failure modes are possible injointed rock and the internal stress distributionwithin a jointed rock mass can be highly complex.Due to large expense and time involved in
experimental studies, coupled with the need forhighly accurate measurement techniques, thestudy of the behaviour of jointed rock usinganalytical models is more promising. There is noprecise method available for modelling the rockmasses, as it is almost impossible to explore all ofthe joint systems or to investigate all theirmechanical characteristics and implementingthem explicitly in a theoretical model. One of themost common ways of determining the rock massstrength is by using a failure criterion.
Many failure criteria are available formodelling rock mass behaviour, viz. Mohr-Coulomb criterion, Bieniawski criterion (1974),Hoek and Brown criterion (1980), Modified Hoekand Brown criterion (1988), Yudhbir criterion[Yudhbir and Prinzl (1983)] and Ramamurthy’scriterion (1993). Most of these rock mass failurecriteria are stress dependent and often include oneor several parameters that describe the rock massproperties. These parameters are usually based onclassification or characterization systems. Thispaper compares two well-established failurecriteria; Hoek and Brown Criterion (1980) andRamamurthy’s criterion (1993) to arrive at the
International Journal of Rock Mechanics & Mining Sciences 38 (2001) 591–598 Technical Note A stress–strain relation for jointed rock masses Fa-quan Wu...
model for hydraulic fracturing of jointed rock masses during HDR stimulation ...Comparison of the analysis results with the data recorded during the ...
for slope stability analysis in situations where the failure mechanism is not...of the strength and deformation characteristics of rock masses are required ...
Deformability characteristics of jointed rock masses under uniaxial compression_专业资料。Itrainlorao nn cec n ehooy221)1-21nenta ulfoJn MiigSineadTcnlg2(...
the joints and rock material respective criteria. ...comparison with a characteristic length of the ...Macroscopic Failure Condition for Jointed Rock Mass...
Macro-mechanical properties of columnar jointed basaltic rock masses 隐藏>> JCn.ot nvTcn1(011:1324 .etSuhUi.eho.21)824—19DoI010/l710105:4:1.07s17...
Failure Properties of Fractured Rock Masses as ...for the failure criterion of a jointed rock mass...the joints and rock material respective criteria. ...
for the failure criterion of a jointed rock mass...the joints and rock material respective criteria. ...A comparison is performed on an illustrative ...
(2005)08–1275–08 ANISOTROPIC YIELD CRITERION FOR JOINTED ROCK MASSES BASED...Formulation of anisotropic failure criteria incorporating a microstructure tensor[...
3 MECHANICAL MODELS AND FAILURE CRITERIA Much effort has been put into ...An anisotropic strength criterion for jointed rock masses (Chen et al., ...
热门文档