组装、冲压、喷漆等专业词汇
Assembly line组装线
Layout布置图
Conveyer流水线物料板
Rivet table拉钉机
Rivet gun拉钉枪
Screw driver起子
Electric screw driver电动起子
Pneumatic screw driver气动起子
worktable 工作桌
OOBA开箱检查
fit together组装在一起
fasten锁紧(螺丝)
fixture 夹具(治具)
pallet栈板
barcode条码
barcode scanner条码扫描器
fuse together熔合
fuse machine热熔机
repair修理
operator作业员
QC品管
supervisor 课长
ME制造工程师
MT制造生技
cosmetic inspect外观检查
inner parts inspect内部检查
thumb screw大头螺丝
lbs. inch镑、英寸
EMI gasket导电条
front plate前板
rear plate后板
chassis 基座
bezel panel面板
power button电源按键
reset button重置键
Hi-pot test of SPS高源高压测试
Voltage switch of SPS
电源电压接拉键
sheet metal parts 冲件
plastic parts塑胶件
SOP制造作业程序
material check list物料检查表
work cell工作间
trolley台车
carton纸箱
sub-line支线
left fork叉车
personnel resource department
人力资源部
production department生产部门
planning department企划部
QC Section品管科
stamping factory冲压厂
painting factory烤漆厂
molding factory成型厂
common equipment常用设备
模具专业英语_英语考试_外语学习_教育专区。 mold 指模子,铸模 mould 指模具,多指塑料模 die指冲模 tooling通常指加工 mould一般会指塑模之类的: die一般会指冷...
模具专业英语 模具零件 mold components 导套 guide bushing 耐磨板:wedge wear plate 定位圈:locating ring 顶板:eracuretun 推杆:push bar 栓打螺丝:S.H.S.B ...
模具专业英语 模具述语 一、 胶口:gate 进胶位: gate location 胶口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 潜水口:...
模具专业英语_机械/仪表_工程科技_专业资料。流道浇口部分: runner system 浇道系统 sprue/cold material trap 浇道/冷料井 sprue puller 拉杆 runner design ...
汽车模具专业英语(中英对照)_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 汽车模具专业英语(中英对照)_机械/仪表_工程科技_专业资料。. Die...
模具专业英语_机械/仪表_工程科技_专业资料。模具方面的专业英语词汇塑料模具 air vent band heater CAV Cavity chip cold slag compre sion molding core cylinder...
模具专业英语1_英语学习_外语学习_教育专区。边钉/导边:leader pin/guide ... pin 波子弹弓: ball catch 模具成形不良用语英汉对照 aberration 色差 bank ...
模具专业术语(英文术语)模具专业术语(英文术语)隐藏>> 模具专业英语时间:2006-8-29 17:05:22 入水:gate 进入位: gate location 水口形式:gate type 转水口:...
模具专业英语词汇一、入水:gate 进入位: gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口: 唧嘴口径:...
模具专业英语_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 模具专业英语_机械/仪表_工程科技_专业资料。今日推荐 ...
热门文档