文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 电子/电路 > M10 Layout guide on 2 layers PCB
侵权投诉

M10 Layout guide on 2 layers PCB

3、 As the 2 layer PCB is always thicker than 1.5mm, it’s hard to design 50 ohm, one way to

reduce the influence from trace mismatch is to reduce the trace length from M10。In the following figure, there’re five place should be point out.

① Antenna matching components should be placed near the antenna connector or

antenna PAD;

② The inhibit area between signal trace and ground should be more than 1.2mm; ③ As the trace is impossible to be 50 ohm impedance controlled, shorten the

length from M10’s signal PAD to the antenna interface. The length should not exceed 10 mm. The signal trace with could according to ⑤.

④ Add GND via near M10’s GND PAD neighbor to the RF signal PAD. These via

is important for RF signal current return. If bipolar antenna is used, the antenna’s ground pole should well connected to the RF signal’s return ground.

⑤ As your board is thicker than 1.5mm, if the RF trace designed as 50 ohm

impedance controlled trace, then the trace width is about 3mm, because this is impossible on the board. The trace width could be as wide as the module PAD.

M10 Layout guide on 2 layers PCB

Figure 3:Reference design of top layer

4、 The bottom layer under the RF path is as following figures. Two points are pointed:

① Keep the ground under the RF trace integrated.

② Via near M10’s ground PAD is important, as described in Figure 3-④. ③ Trace crossing that area is forbidden, as shown in Figure 5.

④ Other signal trace parallel to the RF signal trace should keep a distance

of at least 2mm both on the top layer and the bottom layer, as shown in Figure 6.

上一页第2页

你可能喜欢

热门文档

相关文档

  • spraac5g Implementing DDR2 PCB Layout on the TMS320...

    M10 Layout guide on 2 la... 暂无评价 4页 2财富值 PCB layout 10页 ...No breaks should be allowed in the reference ground layers in this region....

  • PCB layout guide

    PCB layout guide_IT/计算机_专业资料。PCB layout guide印刷电路板布局指导原则技术报告:TR-040 王见名邹应屿 电力电子与运动控制实验室 http://pemclab.cn....

  • Implementing DDR2 PCB Layout on the TMS320DM644x

    PCB Layout Guidelines ... 6页 4下载券 M10 Layout guide on 2 ... ...Two routing layers can share a ground plane (one signal layer above, and...

  • Layout & PCB guideline

    Layout & PCB guideline_电子/电路_工程科技_专业资料。PCB basic knowledge...electrical connections between copper traces on different layers of the board....

  • PCB Layout Guide

    PCB Layout Guide Created by : Cowin Wei Date: 3/02/2006 目录 Spreadtrum solution的特点 的特点 PCB STACK Placement Layout 2010年10月27日 Proprietary and...

  • PCB_LAYOUT guide

    PCB_LAYOUT guide_信息与通信_工程科技_专业资料。PCB LAYOUT guide...Dip 零件 的 Plan Thermal,如下图(二)内框选处: 电感挖空处,all layers ...

  • PCB_Layout_Guide_v10

    17, 2010 PCB Layout Guide 4 AUDIO LAYOUT GUIDELINE a. Audio circuitry ...the audio signal trace should avoid vias on the top and bottom of layers...

  • VIA PCB LAYOUT guide

    VIA PCB LAYOUT guide_信息与通信_工程科技_专业资料。一份不错的布线指导手册Layout Check List Review VIA Confidential Check Item n n n n n n Stack up...

  • DDR2 layout guide

    layout guide 6页 1下载券 ddr layout guide 48页 4下载券 PCB_Layout_... c) Do not divide the two halves of the different pair between layers. ...

  • PCB layout design guide

    (≈0.25mm) Top & inner layers 双层及多层板 20 mils (≈0.5mm) 10 ...m m 制作单位: PDC-HY 保力电子有限公司文件名称:PCB LAYOUT DESIGN GUIDE ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email