运算放大器AD623英文资料
AD623
The output voltage at Pin 6 is measured with respect to thepotential at Pin 5. The impedance of the reference pin is 100k ,so in applications requiring V/I conversion, a small resistorbetween Pins 5 and 6 is all that is needed.

POS SUPPLY
3
OUT6REF5
2
18
Figure 38.Gain Nonlinearity (G = –100, 15 ppm/Div)

NEG SUPPLY
Figure 40.Simplified Schematic
SWING – Volts
The bandwidth of the AD623 is reduced as the gain is increased,since all the amplifiers are of voltage feedback type. At unitygain, it is the output amplifier that limits the bandwidth. There-fore even at higher gains the AD623 bandwidth does not roll offas quickly.
APPLICATIONSBasic Connection
OUTPUT CURRENT – mA
Figure 39.Output Voltage Swing vs. Output CurrentTHEORY OF OPERATION
Figure 41 shows the basic connection circuit for the AD623.The +VS and –VS terminals are connected to the power supply.The supply can be either bipolar (VS = ±2.5 V to ±6 V) orsingle supply (–VS = 0 V, +VS = 3.0 V to 12 V). Power suppliesshould be capacitively decoupled close to the devices powerpins. For best results, use surface mount 0.1µF ceramic chipcapacitors and 10 µF electrolytic tantalum capacitors.
The input voltage, which can be either single-ended (tie either–IN or +IN to ground) or differential is amplified by the pro-grammed gain. The output signal appears as the voltage differencebetween the Output pin and the externally applied voltage onthe REF input. For a ground referenced output, REF should begrounded.
GAIN SELECTION
The AD623 is an instrumentation amplifier based on a modifiedclassic three op amp approach, to assure single or dual supplyoperation even at common-mode voltages at the negative supplyrail. Low voltage offsets, input and output, as well as absolutegain accuracy, and one external resistor to set the gain, make theAD623 one of the most versatile instrumentation amplifiers inits class.
The input signal is applied to PNP transistors acting as voltagebuffers and providing a common-mode signal to the inputamplifiers (Figure 40). An absolute value 50k resistor in eachof the amplifiers’ feedback assures gain programmability.The differential output is
100k
VCVO= 1+
RG
The AD623’s gain is resistor programmed by RG, or more pre-cisely, by whatever impedance appears between Pins 1 and 8.
The AD623 is designed to offer accurate gains using 0.1%–1%tolerance resistors. Table I shows required values of RG forvarious gains. Note that for G = 1, the RG terminals are uncon-nected (RG = ). For any arbitrary gain, RG can be calculatedby using the formula
RG = 100 k /(G – 1)
REFERENCE TERMINAL
The differential voltage is then converted to a single-ended
voltage using the output amplifier, which also rejects any common-mode signal at the output of the input amplifiers.
Since all the amplifiers can swing to either supply rails, as wellas have their common-mode range extended to below the nega-tive supply rail, the range over which the AD623 can operate isfurther enhanced (Figures 19 and 20).
The reference terminal potential defines the zero output voltageand is especially useful when the load does not share a preciseground with the rest of the system. It provides a direct means ofinjecting a precise offset to the output. The reference terminal isalso useful when bipolar signals are being amplified as it can beused to provide a virtual ground voltage. The voltage on thereference terminal can be varied from –VS to +VS.
REV. C













–11–
AD620中文资料 20页 1下载券仪表放大器AD6...本文介绍的可编程增益运算放大器 AD623 很好 的 实现 了这 一功 能 .实 ...
系统中的应用_计算机硬件及网络_IT/计算机_专业资料...奉文介绍的可编程增益运算放大器AD623 禳好驰实褒... 英文刊名: 年,卷(期): 被引用次数: 王建新, ...
AD623单电源_工程科技_专业资料。介绍了AD623单电源的使用方法及设计要点AD623 单电源、电源限输出仪表放大器的原理及应 摘要: 介绍了美国 ADI 公司最新推出的...
AD623仪表放大器在数采系统中的应用-CN_信息与通信_工程科技_专业资料。AD623维普资讯 http://www.cqvip.com 传感器与仪器仪表 仪表放大器 A63D2 在数采系统...
运算放大器实战入门(下)_信息与通信_工程科技_专业资料。运算放大器实战入门(下)运算放大器实战入门( 运算放大器实战入门(下) 云南大学信息学院:何乐生 2010.4...
仪表放大器的应用技巧 长期以来,为仪表放大器供电的传统方法是采用双电源或双极性电源,这具有允许正负输入摆幅和输出摆幅的明显优势。随著元器件技 术的发展,单 ...
仪表运算放大器型号列表_信息与通信_工程科技_专业资料。仪表运算放大器——型号列表制造商 TI 公司 产品类别 仪表运算放大 器 产品型号 INA110KP INA111AP INA114AP...
仪表放大器的正确使用方法_电子/电路_工程科技_专业资料。非常好的资料...由于采用运算放大器,仪表放大器电路 的输入缓冲级 A1 和 A2 可以将信号电压...
6 《前置放大器设计与应用》实验补充资料一、有关...与对共模信号的电压放大倍数 Avc 之比,英文全称是 ...运算放大器和仪表放大器都具有一定的共模抑制特性。 ...
仪表放大器的正确使用方法_信息与通信_工程科技_专业资料。本文介绍了仪表放大...由于采用运算放大器,仪表放大器电路 的输入缓冲级 A1 和 A2 可以将信号电压...
热门文档