Instruction for the set up with the 3D Probe For this operation you need an steel gauge block
1.
2.
3.
4. End the control software Go with the explorer in the directory : D:\rms\Ver_2.xx\Rms6\Basis\Rms6.cfg Make sure that the file Rms6.cfg is not write protected or hidden Open the file and search for : “c_Tlm “ in this section must be
“ @f8RefKorrZKoordinate=0.00000# “
5. Set the value for “ @f8RefKorrZKoordinate=1.00000# “ unequal zero
6. Save the file
7. Close the file
8. Start the control -> “ machine on “ -> set the machine back to machine coodinate ( “Machine coodinates “ -> “ all “ -> OK )
9. Set up a point on a cleaned, plain surface with the 3D probe. The coordinate on the surface should be the negative value of the size of the steel gauge block, you need for the next step.
10. In the same XY- position, put the steel gauge on the surface, put a reference tool in the spindel, and approach with the tip of the tool, exact the top of the gauge.
11. Go to “ Tool length measurement “ -> “ Length measurement “-> select the button “ as reference “ ( The current Z- coordinate is the difference between the probe and the reference tool – this value will be write in the Rms6.cfg automatically) -> press “ OK “
12. Now the machine makes the Length measurement
13. Confirm the result with “ OK “
14. Shut down the control and start again
15. You can find the value now in Rms6.cfg , in the section “c_Tlm “ ->
@f8RefKorrZKoordinate=X.XXXXX#
Set up of a surface with the mechanical 3D - probe :
1. Approach the surface with the probe like in the normal set up.
2. In the window current coordinate, select the button -> “ adapt length correction automatically “ -> OK
3. It is possible, to save the shifting and the TLC value as a pallet coordinatesystem, to call it later on with a NC- command in the program.
Set up of a surface with the automatic 3D probe:
1. Using the automatic 3D probe, it is necessary to set up the coordinate value of the surface before starting the set up process.
2. To accept the result, press the OK button. Now the control will automatically calculate the TLC value, and write all those values in the Metafile.iso.
Instruction for the set up with the 3D Probe For this operation you need an steel gauge block 1. 2. 3. 4. End the control software Go with the ...
ARM Instruction Set 64页 1下载券 INSTRUCTION_FOR_SET_UP 暂无评价 1页 ...SPARC Instruction Set CS 217 Sparc Instruction Set ? Instruction groups load...
Appendix D: Instruction Set Reference This section provides encodings and approximate cycle times for all instructions that you would normally execute in real...
Instruction for AP1, APZ P13.0 CM012 Abstract This document describes the.... . ERROR: Failed to copy c:\acs\logs\lct\SetupService.def to C:\...
INSTRUCTION_FOR_SET_UP 暂无评价 1页 免费 The 80x86 Instruction ... 51...80C88 Instruction Set Summary INSTRUCTION CODE MNEMONIC AND DESCRIPTION DATA ...
Instruction for Life 2页 2下载券 instruction for update 暂无评价 4页 免费 INSTRUCTION_FOR_SET_UP 暂无评价 1页 免费 Instruction for Model... 4页 2...
8051 instruction set and programming8051 ...But for binary and hexadecimal, “B” and “H...When MCS-51 is powered up, the SP register ...
ARM Instruction Set 60页 免费 ARM Instruction Set 64页 2财富值 INSTRUCTION_FOR_SET_UP 暂无评价 1页 免费 The 80x86 Instruction Se... 51页 免费 ...
instruction for update 暂无评价 4页 免费 INSTRUCTION_FOR_SET_UP 暂无评价 1页 免费 Instruction for Life 2页 5财富值 Instruction for Modelte... 4页 5...
INSTRUCTION_FOR_SET_UP 暂无评价 1页 免费 Instruction for Life 2页 2下载券 Instruction for Model... 4页 2下载券喜欢此文档的还喜欢...
热门文档