全部LTE信令流程图
Spec 24.301 5.6.1 “Service Request” Procedure The purpose of the service request procedure is to transfer the EMM mode from EMM-IDLE to EMM-CONNECTED mode and establish the radio and S1 bearers when uplink user data or signalling is to be sent. Another purpose of this procedure is to invoke MO/MT CS fallback or 1xCS fallback procedures. This procedure is used when: 1 the network has downlink signalling pending; 2 the UE has uplink signalling pending; 3 the UE or the network has user data pending and the UE is in EMM-IDLE mode; 4 the UE in EMM-IDLE or EMM-CONNECTED mode has requested to perform mobile originating/terminating CS fallback or 1xCS fallback; 5 the network has downlink cdma2000® signalling pending; or 6 the UE has uplink cdma2000® signalling pending. The service request procedure is initiated by the UE, however, for the d
ownlink transfer of signalling, cdma2000® signalling or user data in EMM-IDLE mode, the trigger is given by the network by means of the paging procedure. The UE shall invoke the service request procedure when: a) the UE in EMM-IDLE mode receives a paging request with CN domain indicator set to "PS" from the network; b) the UE, in EMM-IDLE mode, has pending user data to be sent; c) the UE, in EMM-IDLE mode, has uplink signalling pending; d) the UE in EMM-IDLE or EMM-CONNECTED mode is configured to use CS fallback and has a mobile originating CS fallback request from the upper layer; e) the UE in EMM-IDLE mode is configured to use CS fallback and receives a paging request with CN domain indicator set to "CS", or the UE in EMM-CONNECTED mode is configured to use CS fallback and receives a CS SERVICE NOTIFICATION message; f) the UE in EMM-IDLE or EMM-CONNECTED mode is configured to use 1xCS fallback and has a mobile originating 1xCS fallback request from the upper layer; g) the UE in EMM-CONNECTED mode is configured to use 1xCS fallback and accepts cdma2000® signalling messages containing a 1xCS paging request; or h) the UE, in EMM-IDLE mode, has uplink cdma2000® signalling pending. If one of the above criteria to invoke the service request procedure is fulfilled, then the service request procedure may only be initiated by the UE when the following conditions are fulfilled: its EPS update status is EU1 UPDATED, and the TAI of the current serving cell is included in the TAI list; and no EMM specific procedure is ongoing.

TD-LTE信令流程详解全集_信息与通信_工程科技_专业资料。LTE信令流程 研究院无线所 2010年12月 主要内容基本概念网络架构 协议栈结构 接口功能 无线网系统消息 ...
LTE信令流程 研究院无线所 2010年12月 主要内容基本概念网络架构 协议栈结构 接口功能 无线网系统消息 UE的工作模式与状态 无线承载的分类 UE标识 端到端业务...
LTE系统信令流程(五) 专用承载建立 Dedicated bearer activation (Spec 23.401 5.4.1) UE eNodeB MME Serving GW PDN GW PCRF 1. IP-CAN Session ...
LTE信令流程 研究院无线所 2010年12月 主要内容基本概念网络架构 协议栈结构 接口功能 无线网系统消息 UE的工作模式与状态 无线承载的分类 UE标识 端到端业务...
LTE系统信令流程六_信息与通信_工程科技_专业资料。LTE Handover 信令LTE系统信令流程(六) Handover 切换信令流程 1. E-UTRAN(LTE)内部切换 1.1 基于S1的...
LTE系统信令流程(二) 23.401 5.3.3.1 S-GW改变的TAU信令流程 改变的 信令流程(Tracking Area Update跟踪区更新 跟踪区更新) 改变 信令流程 跟踪区更新 UE ...
LTE典型信令流程分析介绍_生产/经营管理_经管营销_专业资料。LTE... LTE信令流程介绍 43页 1下载券 LTE系统信令流程全集 53页 4下载券 LTE基本...
LTE空口信令流程汇总_生产/经营管理_经管营销_专业资料。今日推荐 ... LTE系统信令流程全集 53页 4下载券 LTE基本信令流程 5页 免费...
LTE系统信令流程(七) Spec 23.401 5.5.2.1.2 E-UTRAN to UTRAN Handover Preparation phase UE Source eNodeB Target RNC Source MME Source Target Target ...
TD-LT 信令流程及信令解码 TD-LTE 信令流程及信令解码 (2013.03) 第 1 页共 81 页 TD-LT 信令流程及信令解码 本文主要就 PS 业务建立流程和 LTE 系统内...
热门文档