文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 医药卫生 > CHARACTERIZATION OF CRYSTALLINE AND PARTIALLY CRYSTALLINE SOLIDS BY X-RAY POWDER DIFFRACTION (XRPD)
侵权投诉

CHARACTERIZATION OF CRYSTALLINE AND PARTIALLY CRYSTALLINE SOLIDS BY X-RAY POWDER DIFFRACTION (XRPD)

USP 35Physical Tests / 941 X-Ray Powder Diffraction427

METHOD III (GRAVIMETRIC)

Procedure for Chemicals—Proceed as directed in the in-dividual monograph preparing the chemical as directedunder Loss on Drying 731 .

Procedure for Biologics—Proceed as directed in the in-dividual monograph.

Procedure for Articles of Botanical Origin—Place about10g of the drug, prepared as directed (see Methods of Anal-ysis under Articles of Botanical Origin 561 ) and accuratelyweighed, in a tared evaporating dish. Dry at 105° for 5hours, and weigh. Continue the drying and weighing at 1-hour intervals until the difference between two successiveweighings corresponds to not more than 0.25%.

arrangement, interferences arise from the scattered X-rays.These interferences are constructive when the path differ-ence between two diffracted X-ray waves differs by an inte-gral number of wavelengths. This selective condition is de-scribed by the Bragg equation, also called Bragg’s law (seeFigure 1).

2dhklsinθhkl = nλ

The wavelength, λ, of the X-rays is of the same order ofmagnitude as the distance between successive crystal latticeplanes, or dhkl (also called d-spacings). θhkl is the angle be-tween the incident ray and the family of lattice planes, andsin θhkl is inversely proportional to the distance between suc-cessive crystal planes or d-spacings.

The direction and spacing of the planes with reference tothe unit cell axes are defined by the Miller indices {hkl}.These indices are the reciprocals, reduced to the next-lowerinteger, of the intercepts that a plane makes with the unitcell axes. The unit cell dimensions are given by the spacingsa, b, and c, and the angles between them α, β, and γ.The interplanar spacing for a specified set of parallel hklplanes is denoted by dhkl. Each such family of planes mayshow higher orders of diffraction where the d values for therelated families of planes nh, nk, nl are diminished by thefactor 1/n (n being an integer: 2, 3, 4, etc.).

Every set of planes throughout a crystal has a correspond-ing Bragg diffraction angle, θhkl, associated with it (for aspecific λ).

A powder specimen is assumed to be polycrystalline sothat at any angle θhkl there are always crystallites in an orien-tation allowing diffraction according to Bragg’s law.2 For agiven X-ray wavelength, the positions of the diffractionpeaks (also referred to as “lines”, “reflections”, or “Braggreflections”) are characteristic of the crystal lattice (d-spac-ings), their theoretical intensities depend on the crystallo-graphic unit cell content (nature and positions of atoms),and the line profiles depend on the perfection and extent ofthe crystal lattice. Under these conditions, the diffractionpeak has a finite intensity arising from atomic arrangement,type of atoms, thermal motion, and structural imperfections,as well as from instrument characteristics.

The intensity is dependent upon many factors such asstructure factor, temperature factor, crystallinity, polarizationfactor, multiplicity, and Lorentz factor.

The main characteristics of diffraction line profiles are 2θposition, peak height, peak area, and shape (characterizedby, e.g., peak width, or asymmetry, analytical function, andempirical representation). An example of the type of powderpatterns obtained for five different solid phases of a sub-stance are shown in Figure 2.

In addition to the diffraction peaks, an X-ray diffractionexperiment also generates a more or less uniform back-ground, upon which the peaks are superimposed. Besidesspecimen preparation, other factors contribute to the back-ground—for example, sample holder, diffuse scattering fromair and equipment, and other instrumental parameters suchas detector noise and general radiation from the X-ray tube.The peak-to-background ratio can be increased by minimiz-ing background and by choosing prolonged exposure times.

An ideal powder for diffraction experiments consists of a large number ofsmall, randomly oriented spherical crystallites (coherently diffracting crystal-line domains). If this number is sufficiently large, there are always enoughcrystallites in any diffracting orientation to give reproducible diffractionpatterns.

2

941 CHARACTERIZATION OFCRYSTALLINE AND PARTIALLYCRYSTALLINE SOLIDS BY X-RAYPOWDER DIFFRACTION (XRPD)

INTRODUCTION

Every crystalline phase of a given substance produces acharacteristic X-ray diffraction pattern. Diffraction patternscan be obtained from a randomly oriented crystalline pow-der composed of crystallites or crystal fragments of finitesize. Essentially three types of information can be derivedfrom a powder diffraction pattern: the angular position ofdiffraction lines (depending on geometry and size of theunit cell), the intensities of diffraction lines (depending

mainly on atom type and arrangement, and particle orienta-tion within the sample), and diffraction line profiles (de-pending on instrumental resolution, crystallite size, strain,and specimen thickness).

Experiments giving angular positions and intensities oflines can be used for applications such as qualitative phaseanalysis (e.g., identification of crystalline phases) and quanti-tative phase analysis of crystalline materials. An estimate ofthe amorphous and crystalline fractions1 can also be made.The X-ray powder diffraction (XRPD) method provides anadvantage over other means of analysis in that it is usuallynondestructive in nature (to ensure a randomly orientedsample, specimen preparation is usually limited to grinding).XRPD investigations can also be carried out under in situconditions on specimens exposed to nonambient conditionssuch as low or high temperature and humidity.

PRINCIPLES

X-ray diffraction results from the interaction between X-rays and electron clouds of atoms. Depending on atomic

There are many other applications of the X-ray powder diffraction techniquethat can be applied to crystalline pharmaceutical substances, such as determi-nation of crystal structures, refinement of crystal structures, determination ofthe crystallographic purity of crystalline phases, and characterization of crys-tallographic texture. These applications are not described in this chapter.

1

第1页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email