文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > The Modulo Time Plot- A Useful Data Acquisition Diagnostic Tool
侵权投诉

The Modulo Time Plot- A Useful Data Acquisition Diagnostic Tool

Abstract--- This paper illustrates the use of the Modulo Time Plot to facilitate diagnosis of data acquisition systems and components. While conventional techniques, involving spectral analysis and histograms, provide certain useful and necessary measures

The Modulo Time Plot - A Useful Data Acquisition Diagnostic Tool Fred H Irons, and Donald M Hummels across the FFT spectrum. A typical situation is depicted in Figures 1 and 2 for an 8-bit ADC. All the examples presented in this paper will have the following common test parameters, namely: NS= 4096, the clock frequency, FS= 204:8 MSPS, and the test frequency, FT= 75:05 MHz. Figure 1 shows acquired sample values versus sample time in sec, and Fig. 2 shows the FFT magnitude spectrum versus FFT bin number. Each of the rst 50 harmonics is labelled if it exceeds a threshold of -75 dB with respect to a fullscale sinewave amplitude. The labeling is (+) for the positive-frequency Euler component and (-) for the conjugate-frequency component. Clearly there are several distortion terms in excess of the noise oor, and clearly the harmonics are distributed across the spectrum by the aliasing process. As a diagnostic tool, the plot shown in Fig. 1 is I. Introduction not very helpful. It does indicate the maximum and It has been understood for several years that dy- minimum sample values, but aliasing hides the fact namic testing of analog-to-digital converters (ADCs) that the sampled signal is a sinusoid. The plot proand waveform recorders is necessary to fully under- vides even less detail when the sample values are constand their performance and useful operating param- nected with straight lines between each data point as eters 1, 2, 3, 4]. The popular dynamic test signal is the graph would turn into a solid black bar between the sinewave because it is easy to generate in near the extrema of the set. Consequently, plots of raw ideal form, i.e., with negligible distortion and highly samples have not been used for signi cant diagnostic accurate and stable frequency. Normally, when NS purposes in the past, other than to construct hissamples are collected and stored in a bu er memory tograms to observe whether there are any missing at a sample rate, FS, the sinewave test frequency is or preferred states. This paper shows how a simple set on one of the basis frequencies, or bins, of the reordering of the sample set can be made to yield FFT associated with the sample set. This frequency visually useful information for diagnostic purposes choice eliminates spreading of signal energy across through the use of the Modulo Time Plot. the FFT spectrum that would otherwise occur. The test frequency is also usually chosen to be in the rst II. The Modulo Time Plot Nyquist band, i.e., less than FS=2, for most applications; however, increased use of IF detection archi- The samples shown in Fig. 1 can be rearranged tectures has pushed testing into second and higher through a straightforward modulo operation which Nyquist bands in many cases. will be developed in this section. The rearrangement Whenever a test frequency is not su ciently less usually provides a clearer picture of both the wavethan FS=2, the harmonic distortion, due to the quan- form properties and the p

erformance of the sampling tizer response to the applied signal, will be aliased device for any periodic test signal. This work has been supported in part by the ARPA Let t represent the time dependence of the kth HBT/ADC program under a contract administered by the Of- sample k the collection of N samples at a constant in S ce of Naval Research Grant N000149311007 and the DEPSCoR program through the Army Research O ce Grant sample frequency, FS . Then Eqn. 1 represents the DAAH04-94-G-0387 set of discrete sample time values based upon the

Abstract| This paper illustrates the use of the Modulo Time Plot to facilitate diagnosis of data acquisition systems and components. While conventional techniques, involving spectral analysis and histograms, provide certain useful and necessary measures of performance, the use of reordered sample sets has gained considerable popularity in recent work aimed at characterizing analog-to-digital converter error mechanisms. Examples show that the Modulo Time Plot is useful for quick visual inspection of system performance including dynamic range, distortion and error plots, the detection of random bit errors, and timing errors between the test signal and the sample clock.

第1页

你可能喜欢

热门文档

相关文档

  • D. Maximum CMRR The

    Correction to “Comments on ‘The Modulo Time Plot: A Useful Data Acquisition Diagnostic Tool’ ” Zsolt P? pay a Fig. 1 Mathcad simulation: spurious ...

  • ACM题目分类

    Modulo Numbers 2000 Gold Coins 2021 Relative ...Plot 1142 Smith Numbers 1188 Gleaming the Cubes ...1676 What time is it? 1684 Dynamic Declaration ...

  • rondeau_sdr2010-grtutorial

    useful stuff gnuradio companion technical stuff ...The QT GUI output offers multiple views: Time (...(idx == len) idx = 0; modulo len idx = (...

  • rondeau_sdr2010-grtutorial

    useful stuff gnuradio companion technical stuff ...The QT GUI output offers multiple views: Time (...(idx == len) idx = 0; modulo len idx = (...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email