辛苦弄得,希望能对你有用处,带来方便
3.3 THE ROLLING RESISTANCE
In order to enable application of a model for the rolling resistance in the finite element model of the belt conveyor an approximate formulation for this resistance has been developed, [8]. Components of the total rolling resistance which is exerted on a belt during motion three parts that account for the major part of the dissipated energy, can be distinguished including: the indentation rolling resistance, the inertia of the idlers (acceleration rolling resistance) and the resistance of the bearings to rotation (bearing resistance). Parameters which determine the rolling resistance factor include the diameter and material of the idlers, belt parameters such as speed, width, material, tension, the ambient temperature, lateral belt load, the idler spacing and trough angle. The total rolling resistance factor that expresses the ratio between the total rolling resistance and the vertical belt load can be defined by:
ft = fi + fa + fb (8)
where fi is the indentation rolling resistance factor, fa the acceleration resistance factor and fb the bearings resistance factor. These components are defined by:
Fi = CFznzh nhD-nD VbnvK-nk NTnT
fa = fb = Fzb t² Fzbri (9)
where Fz is distributed vertical belt and bulk material load, h the thickness of the belt cover, D the idler diameter, Vb the belt speed, KN the nominal percent belt load, T the ambient temperature, mired the reduced mass of an idler, b the belt width, u the longitudinal displacement of the belt, Mf the total bearing resistance moment and ri the internal bearing radius. The dynamic and mechanic properties of the belt and belt cover material play an important role in the calculation of the rolling resistance. This enables the selection of belt and belt cover material which minimise the energy dissipated by the rolling resistance.
3.4 THE BELT'S DRIVE SYSTEM
To enable the determination of the influence of the rotation of the components of the drive system of a belt conveyor, on the stability of motion of the belt, a model of the drive system is included in the total model of the belt conveyor. The transition elements of the drive system, as for example the reduction box, are modelled with constraint conditions as described in section 3.2. A
输送带毕业设计--外文翻译_英语学习_外语学习_教育专区。The Two-Dimensional Dynamic Behavior of Conveyor Belts Ir. G. Lodewijks, Delft University of Technol...
Improved Two-Dimensional Dynamic Batch Process Monitoring with Support Vector ...Actually, the dynamic behavior of the batch process may exist not only ...
An Experimental Investigation on the Dynamic Behavior of Step Motor Drives_专业资料。Junlfcaisniergadtmai 21)3_4 oraoMehnc gnei n otn2(024140 EnAuo ...
Effect of Nb on the dynamic recrystallization behavior of high-grade pipeline steels_专业资料。今日推荐 88份文档 2014年全国注册造价工程师...
Impact of dopants inGaN on the formation of two-dimensional_电子/电路_工程科技_专业资料。Appl. Phys. A 75, 387–389 (2002) / Digital Object Identi...
The Two-Dimensional Dynamic Behavior of Conveyor Belts 3.1.1 NON LINEAR TRUSS ELEMENT If only the longitudinal deformation of the belt is of interest ...
Statistical challenges in the analysis of two-dimensional difference gel ...dynamic range in concentrations; (2) subject-to-subject variability within ...
IFUP-TH 49/92 arXiv:hep-lat/9210011v1 8 Oct 1992 1/N Expansion of Two-Dimensional Models in the Scaling Region ? Massimo Campostrini and Paolo ...
Nonlinear Dynamic Behavior of an Oscillating Tip-Microlever System and Contrast at the Atom In this paper the dynamic behavior of an oscillating tip-...
Solution of the Euler equations on unstructured grids for two-dimensional compressible flow_工学_高等教育_教育专区。关于二维的非结构网格可压流动的求解...
热门文档