DIN-1683-1998
Page4
DIN1683-1:1998-08
7Indicating general tolerances on existing drawings
If an existing drawing does NOT refer to the tolerance groups specified in the 1962 edition of this standard(which is no longer valid), then the tolerance grades given in tables 2 and 3 do not apply. It is recommendedthat a grade suitable for the casting in question be indicated on such drawings.
If an existing drawing DOES refer to the previously valid tolerance groups, it is recommended that these beconverted to the tolerance grades specified in tables 2 and 3 of the present standard. If this is not possible, thelimit deviations are to be taken from tables 6 and 7 below.Tables 6 and 7 do NOT apply to new drawings.
Table 6:Limit deviations for linear dimensions on existing drawings
Nominal size range
Tolerance group
Over
Up to18
up to
Overup to
Overup to
Overup to
Overup to
Overup to
Overup to
Overup to
Overup to
External dimensionsInternal dimensions
Table 7:Limit deviations for thicknesses on existing drawings
Tolerancegroup
Over
Up to18
up to

Overup to
Overup to
Overup to
Overup to
8Indicating machining allowances on existing drawings
The machining allowances specified in this standard only apply to drawings on which general tolerances inaccordance with clause 4 and tables 2 and 3 of this standard are indicated.
Previous editions
DIN 1683-1: 1962-02, 1974-08, 1978-07, 1980-10.
Amendments
As compared with the October 1980 edition, the standard now applies only to castings used for replacementpurposes.
Other relevant standards
DIN 1680-2Rough castings – General tolerances
DIN 1690-1Technical delivery conditions for castings of metallic materials – General
DEUTSCHE NORM December 2006 DIN 509 ICS 01.100.20; 25.020 Supersedes DIN 509:1998-06 D Technical drawings – Undercuts – Types and dimensions ...
2 其它标准和规范若在本标准中不作另行规定,则应同时遵循下述各标准与规范: DIN 4115 DIN 8563 DIN 8563 DIN 15018 DIN 17100 房屋建筑中的轻型钢结构和钢管...
DIN18273-1997 建筑五金件.防火门和防烟门把手组件.术语定义、尺寸、 要求和试验_建筑/土木_工程科技_专业资料。DIN 18273-1997 建筑五金件.防火门和防烟门...
DEUTSCHE NORM Dezember 2004 DIN EN 13209-1 ICS 97.190 X Artikel für ...ndig in den in EN 71-1:1998 festgelegten Prüfzylinder für Kleinteile ...
DIN 19522-2000 铸铁插口排水管和管件_建筑/土木_工程科技_专业资料。铸铁排水管欧洲标准。EN877标准Als Papierkopie - kein ?nderungsdienst / Printed copy - ...
DIN EN 10243-1-2005_专业资料。德标Correction in table 6, last line, ... DIN EN 1748-1-1-2004 DIN EN 1876-1-1998 DIN EN 10083-1-1996...
(includes amendment A1:2001); German Version EN 10222-4:1998 + A1:2001 { EN 10222-4 Ersatz für DIN EN 10222-4:1999-02 Pièces forgées ...
德国的文本 EN 50625-2-2 : 1998。 DIN EN5 0625-2-4 (VDE 0482 部分 266-2-4) 公共的检验情况用于在燃烧情况下的电线和绝缘体导线—由电线以及绝缘体 ...
0104 第 2 页 DIN 5480 第 11 部分 模数 6 (ρ fmin = 0,96)(关于插图1,请参见第1页)表1 基本尺寸 基准直径数 齿度圆直径 z 分圆直径 基径顶圆直...
Din 40431-2 塞规_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 Din 40431-2 塞规_机械/仪表_工程科技_专业资料。 ...
热门文档